Jeep Wrangler TJ 3D-printable parts

Flexible gasket that seals between the rectangular taillight housing and lens. The source specifies TPU and the mounting pattern is documented across late CJ, YJ and TJ applications.

Replacement door-hinge liners with separate early, later and driver-side printable variants. Source naming and year-marked files support late CJ, YJ and TJ applications.

Driver- and passenger-side replacement handles for paddle-style doors. The creator tested the design in a 1981 CJ-7 and states YJ and TJ compatibility, while warning that earlier non-paddle doors differ.

Replacement lower bracket for the automatic-transmission shift-indicator assembly used across the 1997–2006 Wrangler TJ. The printed bracket accepts the original upper cover and hardware.

Small-diameter bow knuckle used by the creator to convert a factory TJ soft top to a flip-up configuration.

Exact-replica replacement foot for the removable rear bench seat, modeled from the part in a 2000 Wrangler Sport and designed to reuse the original embedded washer and screw.

Two-piece replacement for the heat-damaged European-market license-plate light mounting and outer cover, designed around LED illumination on a 2004 Wrangler TJ.

Replacement end cap for the stock 1997–2006 Wrangler TJ rear bumper. The creator test-fitted the design on a European-market TJ.

Large hand knob for converting TJ hardtop fasteners to tool-free quick-release hardware. The model is sized for a captured bolt and broad hand grip.

Replacement end cap for the stock 1997–2006 Wrangler TJ front bumper. Two copies complete the bumper.

Three-piece wall-mount system that supports removed TJ doors from their factory hinge points instead of the window frame. The creator printed and load-tested the PETG design.

Replacement bushing that removes play from the tilting passenger-seat slide mechanism on the 2002 Wrangler TJ.

Adapter that fits a short, wide Toyota-pattern push switch into the factory Jeep switch panel. The creator specifies 1997–2004 Wrangler TJ and 1997–2001 Cherokee XJ applications.

Hinged hook sized around the TJ's approximately three-inch padded roll bar. The revised left and right halves add a lower M3 closure to prevent spreading when unloaded.

Protective clips that snap over the lower edges of removed TJ doors before they are set on concrete or sand.

Left and right faceplates and enclosures that replace the TJ's front dashboard speaker mounts with 5.25-inch pods. The creator printed, installed and evaluated the complete set.

Flexible replacement sleeve for either end of the TJ soft-top tailgate bar. The creator modeled the combined rubber-and-plastic original as a single TPU part.

Snap-in blanks for the 2001 TJ center-console switch opening, supplied as a plain filler and a version for a common round rocker switch.

Replacement nut clip for the screws that secure the TJ's chrome headlight trim ring when the original clips strip.

Adapter ring that mounts a 6.5-inch speaker in the factory TJ speaker pod without modifying the pod, using the original vehicle hardware and four M3 speaker screws.

Snap-in replacement bracket that secures the manual-transmission shifter boot to the TJ center console, modeled from the broken original and test-fitted in PETG.

Large-drink cupholder that bolts to the rear seat-mount area. The creator explicitly identifies and photographed TJ and JK fitment.

Replacement geared and plain internal flaps for a TJ dashboard vent that can no longer close.

Quarter-turn threaded replacement floor plug tested in a 1998 TJ. The slot accepts a US quarter as an installation tool.

Replacement mounting bracket and pivot pin for the factory Hella fog light used on 2004–2006 Wrangler TJ models, supplied as both a one-piece print and a reinforced multipart option.

Full replacement interior release handle modeled after the TJ original. The creator installed the design and reported it still working after approximately nine months.

Replacement hood-mounted clip for the prop rod on a 1997 Wrangler TJ, with the round hood-hole mount verified by the creator.

OEM-shaped replacement rotary heater and air-conditioning control knob for 1999–2001 Wrangler TJ dashboards, measured from original controls and physically installed by the creator.

OEM-shaped replacement heater-control knob for the 1997 Wrangler TJ, measured from an original control and physically installed by the creator.

Springless replacement for the failure-prone upper soft-door window latch, measured from the factory part and installed on the creator's Wrangler.

Tight-fitting flexible replacement end for a TJ sun visor pivot.

Replacement rotary air-conditioning control knob for the 2006 Wrangler TJ, including a small hole for a contrasting filament position marker.

Drop-in organizer tray for the upper center console of a 1997 TJ, designed to print without supports and test-fitted by the creator.

Flexible replacement tether sized for the stock 1997–2006 TJ fuel cap, with a split ring that allows installation without removing the cap.

Two-piece replacement visor clip with a push latch: lift the latch to release the visor and press it down to lock the visor in place.

Replacement internal divider that prevents red and white light bleed inside the TJ taillight after the original metal separator rusts away.

Tested replacement fan-control knob for the 2004 Wrangler TJ, designed to reuse the metal insert from the broken original.

Replacement treble and bass adjustment button for the stock TJ radio.

Straight replacement connector for the failure-prone flip-back hinge in the Rugged Ridge TJ soft-top frame. The non-hinged design fits inside the original tubes.

Paired adapter nuts that allow Mercedes-pattern door-jamb switches to replace the TJ switches on both sides.

Clamp-style repair for a broken early-TJ temperature-control cable end, modeled and installed on a 1997 Wrangler.

Replacement holder for a 5/16-inch square hardtop mounting nut, modeled from the retainers found in the creator's TJ.

Complete repair set for the missing or cracked center and side vents in a 2002 TJ, including housings, vanes, sliders and geared control pieces. The creator printed prototypes and specifies heat-resistant material for service use.