Browse the parts catalogue

Mirror brackets that bolt to the existing windshield-frame fastener points. The source provides an original bracket plus left- and right-hand variants and describes the installed design as rigid and simple to fit.

Replacement end clip for broken mechanical heater-control cables. The creator verified it on 1991 controls and identifies select CJ, YJ and XJ applications; fit and cable travel should be checked before reassembly.

Replacement clip that retains a door latch push rod. It was modelled from an intact original and the creator reports that it clipped correctly into the door.

Three-piece replacement cupholder with a 3.5-inch front pocket, a 1.91-inch rear pocket and a separate base that can be glued or screwed in place.

Snap-in plug for a flat one-inch floor drain hole. The source warns that a hole crossing a floor bend may need a slightly smaller plug.

Screw-on T-handle replacement for the parking-brake release control. The physical source photographs show the printed handle fitted below the dashboard.

Spacer arm that lets a factory replacement turn-signal stalk operate the exposed washer-pump switch when the original cover is missing. The creator fitted a PETG print after light sanding.

Blank snap-in center cap modelled to replace a cap on 1991 wheels. The source also preserves an editable STEP file, while the catalogue download is the printable STL.

Close factory-style replacement for the rotary heater and air-conditioning blower knob, modelled directly from a 1991 control.

Modular enclosures for 5.25-inch speakers that clamp around a 58 mm roll bar using M4 hardware. Sealed, accessory-port and left/right variants are included, and the creator reports the installed system fits and works.

Flexible replacement gasket for a windshield-washer nozzle. The creator made it thicker than the shrunken originals and reports a good fit when printed solid in flexible filament.

Printable rear lamp housing with deeper lens-screw holes, a wiring opening and internal rails for the included red-and-clear lens separator. The source recommends heat-resistant material and provides both printable parts.

Flexible gasket that seals between the rectangular taillight housing and lens. The source specifies TPU and the mounting pattern is documented across late CJ, YJ and TJ applications.

Printable rectangular taillight lens for the standard late-CJ and YJ rear lamp housing. The creator printed it in clear ABS for use with red and white LED bulbs.

Bracket for relocating a winch-controller jack into a grille slot. Exact grille spacing should be checked before drilling or wiring; speculative CJ and TJ fitment was not assigned.

License-plate bracket with a channel for an LED strip and a separate clear printable lens. The two-part design mounts in the stock late-CJ and YJ location.

Rear-seat cupholder that slides into the factory soft-top track and is retained by an existing track screw. The creator recommends high infill around the mounting tabs and upright.

Replacement door-hinge liners with separate early, later and driver-side printable variants. Source naming and year-marked files support late CJ, YJ and TJ applications.

Twist-on replacement cap for the windshield-washer fluid reservoir. The source notes that reservoir use requiring a vent tube is a different configuration and was not claimed.

Driver- and passenger-side replacement handles for paddle-style doors. The creator tested the design in a 1981 CJ-7 and states YJ and TJ compatibility, while warning that earlier non-paddle doors differ.

Replacement slider knob for the defrost, heater and vent controls. It was measured from a broken original, physically compared with the original and test-fitted successfully.

Replacement retaining clip for the 2.5-litre airbox. The creator trial-fitted nylon prints on a 1990 vehicle, road-tested them and explicitly identifies the matching Comanche application.

Hooks that slip under the soft-top rails and accept shock cord or resized paracord to keep the folded top from moving.

Two low-profile front turn-signal housings for LED conversions, with 12-by-12 and 20-by-20 heatsink openings. The creator installed the design to gain intercooler clearance while retaining the original lamp location.

Close replica of the factory dashboard switch plate with openings for three standard toggle switches. The creator printed and installed the panel in PETG.

Cupholder that uses the stock windshield-mount-plate holes on late CJ and YJ vehicles without the factory dash pad. It is sized for a mug with a carabiner handle and the creator test-fitted a PETG print.

Four-piece left- and right-hand replacement set for the discontinued soft-top bow ends. Physical photographs compare the printed parts with the originals and show the assembly positioned on the body rail.

Paired stops that fit around the mirror-arm mounting nuts to limit mirror movement. The creator installed ABS prints and provides fitting cautions for seating the nut without overloading the part.

Two printable plastic spacer components for repairing the horn-button assembly. The source only verifies the YJ application, so other same-era vehicles were not linked.

Slip-on clip that holds the door courtesy-light switch open so the interior lights remain off when the doors are removed. It was designed around the pictured replacement switch.

Separate circular and rectangular flexible liners that replace the original rubber center-console insert without print supports. The physical photograph documents the original one-piece texture and layout.

Left- and right-hand replacements for the break-prone plastic soft-top rail pins or sliders used on 1991 vehicles. Both original downloadable meshes are included.

Replacement lower bracket for the automatic-transmission shift-indicator assembly used across the 1997–2006 Wrangler TJ. The printed bracket accepts the original upper cover and hardware.

Small-diameter bow knuckle used by the creator to convert a factory TJ soft top to a flip-up configuration.

Exact-replica replacement foot for the removable rear bench seat, modeled from the part in a 2000 Wrangler Sport and designed to reuse the original embedded washer and screw.

Two-piece replacement for the heat-damaged European-market license-plate light mounting and outer cover, designed around LED illumination on a 2004 Wrangler TJ.

Replacement end cap for the stock 1997–2006 Wrangler TJ rear bumper. The creator test-fitted the design on a European-market TJ.

Large hand knob for converting TJ hardtop fasteners to tool-free quick-release hardware. The model is sized for a captured bolt and broad hand grip.

Replacement end cap for the stock 1997–2006 Wrangler TJ front bumper. Two copies complete the bumper.

Three-piece wall-mount system that supports removed TJ doors from their factory hinge points instead of the window frame. The creator printed and load-tested the PETG design.

Replacement bushing that removes play from the tilting passenger-seat slide mechanism on the 2002 Wrangler TJ.

Adapter that fits a short, wide Toyota-pattern push switch into the factory Jeep switch panel. The creator specifies 1997–2004 Wrangler TJ and 1997–2001 Cherokee XJ applications.

Hinged hook sized around the TJ's approximately three-inch padded roll bar. The revised left and right halves add a lower M3 closure to prevent spreading when unloaded.

Protective clips that snap over the lower edges of removed TJ doors before they are set on concrete or sand.

Left and right faceplates and enclosures that replace the TJ's front dashboard speaker mounts with 5.25-inch pods. The creator printed, installed and evaluated the complete set.

Flexible replacement sleeve for either end of the TJ soft-top tailgate bar. The creator modeled the combined rubber-and-plastic original as a single TPU part.

Snap-in blanks for the 2001 TJ center-console switch opening, supplied as a plain filler and a version for a common round rocker switch.

Replacement nut clip for the screws that secure the TJ's chrome headlight trim ring when the original clips strip.

Adapter ring that mounts a 6.5-inch speaker in the factory TJ speaker pod without modifying the pod, using the original vehicle hardware and four M3 speaker screws.

Snap-in replacement bracket that secures the manual-transmission shifter boot to the TJ center console, modeled from the broken original and test-fitted in PETG.

Large-drink cupholder that bolts to the rear seat-mount area. The creator explicitly identifies and photographed TJ and JK fitment.

Replacement geared and plain internal flaps for a TJ dashboard vent that can no longer close.

Quarter-turn threaded replacement floor plug tested in a 1998 TJ. The slot accepts a US quarter as an installation tool.

Replacement mounting bracket and pivot pin for the factory Hella fog light used on 2004–2006 Wrangler TJ models, supplied as both a one-piece print and a reinforced multipart option.

Full replacement interior release handle modeled after the TJ original. The creator installed the design and reported it still working after approximately nine months.

Replacement hood-mounted clip for the prop rod on a 1997 Wrangler TJ, with the round hood-hole mount verified by the creator.

OEM-shaped replacement rotary heater and air-conditioning control knob for 1999–2001 Wrangler TJ dashboards, measured from original controls and physically installed by the creator.

OEM-shaped replacement heater-control knob for the 1997 Wrangler TJ, measured from an original control and physically installed by the creator.

Springless replacement for the failure-prone upper soft-door window latch, measured from the factory part and installed on the creator's Wrangler.

Tight-fitting flexible replacement end for a TJ sun visor pivot.

Replacement rotary air-conditioning control knob for the 2006 Wrangler TJ, including a small hole for a contrasting filament position marker.

Drop-in organizer tray for the upper center console of a 1997 TJ, designed to print without supports and test-fitted by the creator.

Flexible replacement tether sized for the stock 1997–2006 TJ fuel cap, with a split ring that allows installation without removing the cap.

Two-piece replacement visor clip with a push latch: lift the latch to release the visor and press it down to lock the visor in place.

Replacement internal divider that prevents red and white light bleed inside the TJ taillight after the original metal separator rusts away.

Tested replacement fan-control knob for the 2004 Wrangler TJ, designed to reuse the metal insert from the broken original.

Replacement treble and bass adjustment button for the stock TJ radio.

Straight replacement connector for the failure-prone flip-back hinge in the Rugged Ridge TJ soft-top frame. The non-hinged design fits inside the original tubes.

Paired adapter nuts that allow Mercedes-pattern door-jamb switches to replace the TJ switches on both sides.

Clamp-style repair for a broken early-TJ temperature-control cable end, modeled and installed on a 1997 Wrangler.

Replacement holder for a 5/16-inch square hardtop mounting nut, modeled from the retainers found in the creator's TJ.

Complete repair set for the missing or cracked center and side vents in a 2002 TJ, including housings, vanes, sliders and geared control pieces. The creator printed prototypes and specifies heat-resistant material for service use.

Clip-in defrost-air diverter for 2007–2010 Wrangler JK dashboards. It redirects air from the short factory grille toward the outer windshield edges.

Replacement carpet retaining clip for the Wrangler JK. The creator identifies six locations under the dash and seats where this printed fastener replaces a missing clip.

Auxiliary round-rocker switch panel shaped to the curved radio bezel used on 2011–2018 Wrangler JK and JKU interiors. Installation requires holes behind the panel.

Protective cover for the exposed front vacuum pump on a 2016 Wrangler JK after installation of an open aftermarket bumper. Check bumper clearance before use.

A-pillar mounting post for a RAM-style arm in a Wrangler JK. The design installs with a 5/16-inch by 90 mm socket-head cap screw.

Hand wrench for loosening and tightening Wrangler JK Freedom-panel knobs without straining fingers. Two grip profiles are included.

Reinforced 24 mm socket for the Pentastar oil-filter housing used in Wrangler JK models. This V2 geometry accepts either a 3/8-inch or 1/2-inch drive; the creator tested the earlier PLA version to the 25 N·m service torque.

Replacement clip that secures the interior door-handle release cable on Wrangler JK doors. The creator recommends a heat-resistant, slightly flexible material.

Thin snap-on protector for Wrangler JK door hinges that shields painted hinge faces from gravel impacts. This entry uses the creator's latest bulged-fit revision.

Bushing spacer developed on a 2008 Wrangler JK to secure a loose front inner-fender splash guard after custom fenders were fitted.

Extender that restores contact between the Wrangler JK tailgate bump stop and a spare tire after fitting offset aftermarket wheels. It accepts the original bump stop and an added rubber isolator.

One-piece rigid replacement for a torn Wrangler JK front-door mesh pocket. Mirror the model in the slicer for the opposite door.

Drop-in organizer for the small console recess ahead of the automatic shifter in a 2010 Wrangler JK or JKU. It provides coin slots and a cylindrical holder.

Factory-style under-hood switch panel for a Wrangler JK fitted with an ARB Twin compressor. Versions with and without a reinforced quick-connect air-chuck opening are included.

Holder for a 14 mm aftermarket hands-free microphone in the factory UConnect microphone position of a Wrangler JK. Rounded and squared holder variants are included.

Replacement climate-control knob shell modeled for a 2010 Wrangler JK dashboard. Confirm shaft fit before pressing it fully into place.

Large spiked washer that spreads the load of the factory 10 mm heat-shield fastener on a Wrangler JK subframe. The creator specifies solid, high-temperature tough material and used glass-filled nylon; sandwich it under a metal washer.

Replacement arrow-head retaining clip modeled from the Wrangler JK rear fender-flare fastener. Print in a strong, heat-resistant material with controlled flex.

Snap-fit replacement cap for the automatic shifter knob in a Wrangler JK. The model is designed to retain like the original cap; a small amount of removable hot glue can add security.

Flexible replacement mounting grommet for the engine appearance cover on approximately 2012–2016 Wrangler JK models.

Replacement bracket for the factory subwoofer enclosure in a Wrangler JK. It substitutes for the original metal piece when corrosion has damaged it.

Push-fit center cap for Wrangler JK steel wheels with an approximately 65 mm center bore and 84 mm outer face. This entry uses the creator's plain, no-logo geometry.

Printable floor drain plug stated by the creator to fit Wrangler JK, Wrangler JL, and Gladiator JT floors and compatible drain openings in their floor mats. This entry contains only the functional plug body.

Low-profile fog-light mount for a Wrangler JK aftermarket bumper where a winch interferes with the factory cup. It moves the original fog lamp forward approximately 13 mm.

Right-hand passenger sun-visor pivot mount modeled after the broken mount in a Wrangler JK. It allows repair without replacing the complete visor assembly.

Three-piece flexible replacement tether for the Wrangler JK fuel cap. The pins are intentionally snug and may be warmed slightly for assembly.

Replacement cylindrical roller for the Wrangler JK sun visor. It restores a firm grip in the visor clip so the visor stays stowed, including during off-road use.

Printable hand knob assembly for Wrangler JK Freedom-panel bolts. It captures an M8 × 1.25 × 75 mm bolt for tool-free panel retention.

Replacement raised-number insert for the automatic shifter knob in a Wrangler JK.

Hook that holds the Wrangler JLU rear under-floor cargo hatch open by connecting its nylon loop to the child-seat anchor bar.

Flexible fitted liner for the factory cup-holder recess in a Wrangler JL center console.

Inner bushing for the Rampage Hi-Lift jack carrier that limits fore-and-aft movement of its horizontal carry bolt and reduces rattling. The creator states JK and JL fitment.

Outer bushing that fits a Hi-Lift jack climber rung around the Rampage carrier bolt to suppress rattling. The creator states JK and JL fitment.

Modular Wrangler JL dashboard-rail mounting set with heat-resistant printable bases, arms, 20 mm ball adapters, magnetic base, and left/right holders for 67 Designs-compatible rails.

Three-hole adapter ring for fitting a Kicker-style 4-inch replacement speaker in the factory Wrangler JL or Gladiator JT speaker location.

Two-piece Wrangler JL dash-camera mount that clamps at the rear-view mirror area and remains usable with the windshield folded. It assembles with an M4 fastener.

Clip-on CB radio microphone holder for the passenger grab handle in a Wrangler JL.

No-drill mount for a Midland MXTA25 low-profile antenna on the internal sport-bar fastener of a two-door 2018-and-newer Wrangler JL. The location is shared with soft-top hardware.

Printable W-type retaining clip sized for the fender-flare slots on 2018-and-newer Wrangler JL and compatible Gladiator JT applications. This entry uses the creator's support-free revision.

Service tool for removing a stubborn Wrangler JL wiper arm before folding the windshield. It uses a standard 1/4-inch bolt and nut.

Friction-fit auxiliary switch panel for 2018-and-newer Wrangler JL models without power windows. It accepts four 19 mm round switches and one rocker switch.

Insert used in pairs to fill the license-plate mounting holes in an AEV rear bumper before the plate screws are installed on a Wrangler JL.

Press-fit removable cover for the exposed door-lock keyhole on Wrangler JL and JLU models.

Friction-fit blank faceplate for the left dashboard cubby on 2018–2021 Wrangler JL models equipped with factory auxiliary switches.

A-pillar mount with two 20 mm accessory balls for Wrangler JL and Gladiator JT. It reuses the factory pillar bolt with a smaller replacement washer.

Updated airflow-control plugs for the Wrangler JL dashboard defroster grille. The creator recommends ASA for cabin heat and UV stability.

Bumper adapter for installing a three-inch pod light in a Wrangler JL fog-light opening. The creator reports successful use and recommends ABS, PETG, or ASA.

Tool-free magnetic holder for a Tazer JL Mini module under the dashboard of Wrangler JL or Gladiator JT models. It uses five 12 by 3 mm magnets and leaves the status light and USB port accessible.

Eight-millimeter gauges used when manually calibrating Freedom-panel position on Wrangler JL, JLU, and Gladiator JT roofs.

Reinforcement plate for the failure-prone Wrangler JL sun-visor pivot. This revised remix adds beveled screw holes, tapered ends, and locating extrusions in the original holes.

Engine-bay bracket for mounting a Garmin PowerSwitch and an adjacent winch relay in a Wrangler JL.

Blank and left/right RJ45 faceplates for the Wrangler JL Rubicon left dashboard cubby. The connector openings fit extensions used with Midland MXT275 and MXT575 radio handsets.

Single auxiliary-light bracket for the cowl or lower A-pillar mounting area of a Wrangler JL.

Replacement door-speaker grille for full-size Jeep doors. The source photograph compares the printed grille with the surviving factory grille frame.

Auxiliary switch panel for a 2000 Cherokee XJ that mounts ahead of the shifter with automotive double-sided tape. Single rectangular, three rectangular, and round-rocker layouts are included.

Solid replacement knob for the manual window crank on a 1993 Cherokee XJ. The creator omitted the weak pre-cut shaft opening so the crank pin forms its own tight fit during installation.

Slotted replacement for the failed plastic pivot in a Cherokee XJ electric door mirror. The slot lets the wiring pass through so the mirror does not need complete disassembly.

Removable twin cup holder for the rear of a 2001 Cherokee XJ center console. The armrest passes through the frame to retain it, and the cup inserts lift out for cleaning.

Twin cup holder shaped for the parking-brake area of a 1984–1996 Cherokee XJ center console.

Dashboard bracket for mounting an aftermarket single-DIN stereo in a 1997–2001 Cherokee XJ.

Small right-side lower trim replacement for a pre-facelift four-door Cherokee XJ, positioned between the passenger door and rear wheel arch. It is not intended for the two-door body.

Replacement bracket that supports the retractable cargo cover directly behind the rear seats of a Cherokee XJ.

Clear-print replacement lens for the rear cargo lamp in a pre-facelift Cherokee XJ. The creator notes that its edges are straight rather than curved like the original.

Glue-on repair bases for broken trim-clip mounts on the Cherokee XJ tailgate cover. Standard and short bases are included for the different factory positions.

Multi-piece left- and right-side replacement end caps for factory Cherokee XJ side steps. The sections are bonded after printing and the screw piece must be tapped before installation.

Two-piece puller for removing a seized AW4 automatic-transmission neutral-safety switch without prying on it. It uses an M8 nut and bolt to draw the switch from its shaft.

Replacement center-dash switch carrier for a 1997–2001 Cherokee XJ. It holds six factory-style switches plus one round 12-volt accessory socket.

Clip-on retainer that holds a broken rear washer nozzle together on a 1997–2001 Cherokee XJ wiper arm without adhesive.

Replacement rear hooks for the retractable privacy cover in a 1984–1996 Cherokee XJ cargo area. Original-position and 12 mm inboard left/right versions are included.

Plain push-fit center cap modeled for the approximately 64 mm stock wheel opening on a 1992 Cherokee XJ. This entry excludes the decorative lettered variant.

Clock-delete switch panel developed on a 1989 Comanche MJ and stated by the creator to fit the Cherokee XJ dashboard. Blank and pre-drilled switch layouts are included.

Replacement captive screw-nut insert for the Cherokee XJ front grille. The creator recommends PETG or ABS for service temperature and durability.

Replacement retaining bracket for the Cherokee XJ cargo area, designed to print on its side with support.

Replacement sun-visor retaining clip modeled for an 1980s Cherokee XJ. The creator used PETG for the installed parts.

Replacement hood-prop rod holder for RENIX-era Cherokee XJ and Comanche MJ vehicles. The creator does not claim fitment on 1997–2001 Cherokees.

Taller replacement button for a Cherokee XJ roof-rack rail. The revised height and outer-face recess correct rocking seen with the earlier geometry.

Plain center cap sized for the 16-inch ICON wheels on a 2001 Cherokee XJ Classic. Confirm the wheel opening before printing for a different stock wheel.

Drop-in storage pocket that replaces the ashtray in a Cherokee XJ center dashboard.

Reinforced replacement for the failure-prone automatic-transmission selector insert in a 1997–2001 Cherokee XJ. This entry uses the creator's final second revision.

Flexible replacement stop for a Cherokee XJ glovebox. The creator printed it in TPU to reproduce the original rubber function.

Door-corner pod for installing the creator's specified aftermarket tweeter in a 1997–2001 Cherokee XJ. Confirm tweeter diameter before printing.

Load-spreading washer that repairs broken dashboard material around the headlight switch on a 1984–1996 Cherokee XJ. Its diameter can be scaled for a larger damaged area.

Adapter bracket used on a 1999 Cherokee XJ to cover the original rear mounting holes while attaching a European-format license-plate holder.

Simple spacer used to retain a replacement blower motor in a Cherokee XJ heater housing.

Center-dash panel for installing two round 12-volt accessory sockets in a Cherokee XJ.

No-drill rain-gutter bracket for mounting small side floodlights on a 2001 Cherokee XJ. The latest hooked, hex-head V5 geometry is included.

Adapter ring for mounting Hertz X130-size replacement speakers in the rear roof positions of a 1997–2001 Cherokee XJ with the Infinity system.

Replacement transfer-case shift-indicator plate and insert for the floor console used in Cherokee XJ and Comanche MJ vehicles. The blank surface can be lettered or backlit.

Driver- and passenger-side replacement mirror mounts for 1984–1996 Cherokee XJ doors. Easy slotted and full replacement versions support manual or electric mirrors.

Replacement roof-rack rail stanchion buttons for the 1996 curved and 2000 Cherokee XJ profiles.

Replacement clip that stows the hood support rod on a 1989 Cherokee XJ.

Direct replacement windshield-washer nozzle for a 1989 Cherokee XJ, revised with three spray ports and reinforced hose-barb and mounting joints.

Replacement exterior antenna mounting flange for a 1989 Cherokee XJ. The creator notes that its outside diameter is smaller than the original.

Glue-on replacement anchor for broken rear-hatch trim mounting points on a 1989 Cherokee XJ. The source describes reinforced epoxy bonding to the remaining plastic.

Replacement shim for a missing rear-seat hinge pin isolator on a 1989 Cherokee XJ.

Removable collar and flat-bottom insert that stabilize smaller cups in the rear cupholder of a 1997–2001 Cherokee XJ center console.

Switch plate for the ashtray opening in a 2000 Cherokee XJ. Functional five-hole and blank versions are included

Clamp-style mount for adding a gauge to a Cherokee XJ steering column without drilling the column trim.

Clock-delete panel for a Cherokee XJ or Comanche MJ dashboard that accepts one 52 mm gauge and two rocker switches.

Three-inch plug for the large driver- and passenger-side front floor openings in a 1984–1996 Cherokee XJ. Fitment on 1997–2001 vehicles is not claimed.

Replacement latch for the center-console lid on a 1997–2001 Cherokee XJ. The source recommends an angled print orientation to improve strength.

Flexible sealing plug for the interior body antenna pass-through on a 1995 Cherokee XJ. This is not the exterior fender-top plug.

Replacement latch for the center-console lid on a 1984–1996 Cherokee XJ, with an orientation guide for improved layer strength.

Press-fit dashboard mount measured for an Auxbeam six-gang controller in a 1998 Cherokee XJ. The creator states that the first release had not yet been test-fitted.

Replacement trim bezel around the front-seat folding lever in a two-door Cherokee XJ. The same geometry fits either seat side.

Removable storage bin and lid for the small rear cupholder in a Cherokee XJ center console.

Dimensionally matched replacement blank for unused dashboard switch openings in 1984–1996 Cherokee XJ and Comanche MJ interiors.

Oval firewall grommet for the 4.0L engine-control harness in 1984–1996 Cherokee XJ and Comanche MJ vehicles. Print in a suitable flexible, heat-resistant material.

Solid replacement cap for the engine-bay relay cover used on 1984–1996 Cherokee XJ and Comanche MJ vehicles. Use a high-temperature material.

Replacement center-vent body that holds a 52 mm auxiliary gauge in a Cherokee XJ dashboard.

Replacement sliding cover for the Cherokee XJ automatic gear selector. The reinforced face installs downward and the creator recommends semi-flexible filament.

Purpose-built wrench for removing a seized Cherokee XJ fuel-pump retaining ring without striking the ring with a hammer and screwdriver.

Replacement slotted insert modeled from a surviving 1997–2001 Cherokee XJ grille insert. The creator recommends minor scaling if required for the individual grille.

Replacement dashboard bezel for mounting a single-DIN radio in a Cherokee XJ. It is oriented to fit a 220 × 220 mm print bed.

Replacement brackets and spacers that support the pop-up air dam on the sliding Sun-Rider roof fitted to a Jeep Liberty KJ. The creator modeled them from the original parts and used the printed set successfully.

Multi-piece snap-in center cap modeled for the approximately 55–56 mm wheel opening on a 2004 Jeep Liberty KJ. This entry uses the creator's plain top and excludes the decorative lettered top.

Removable coin cup and riveted docking adapter shaped for the Jeep Liberty KJ center console. The cup is sized for US coins.

Replacement center fin for a broken dashboard air vent in a 2003 Jeep Liberty KJ. The creator notes that the end pins may require light sanding for fit.

Replacement rear cargo-area tie-down loop for a 2005 Jeep Liberty KJ, developed after the original riveted loop was damaged during carpet removal. The source includes installed validation photographs.

Replacement retaining clip for the windshield defrost vent in a Jeep Liberty KJ dashboard.

Replacement fader-control knob for the factory radio in a Jeep Liberty KJ. The creator recommends a heat-resistant material suitable for a parked vehicle interior.

Dashboard pod for two auxiliary gauges in a Cherokee KJ or Liberty KJ. It fits without drilling or cutting the instrument panel.

Reinforced replacement sun-visor clip for a Jeep Liberty KJ. This revision adds a small retention bump so the visor clicks securely into the clip.

Hand tool for releasing the fuel-line quick connector on a 2005 Cherokee KJ or Liberty KJ.

Replacement louvre linkage arm and five blade profiles for repairing the dashboard air vents in a 2005 Jeep Liberty KJ. The submitted meshes preserve the source geometry while reducing excessive tessellation for the API.

Shorter replacement radio antenna developed for a 2008 Jeep Liberty KK to clear a garage door. Plain and captured-nut bases, the wire support, and weather radome are included; assembly requires an M5 fastener and antenna wire.

Replacement internal gear for a clicking HVAC blend-door actuator in a 2010 Jeep Liberty KK. The creator installed the printed gear and reports that the actuator operates.

Coin organizer shaped for the lower-right dashboard panel in a 2011 Jeep Liberty KK. It mounts with automotive trim tape after cleaning the panel.

Replacement retaining clip for the headlight and fog-lamp service access cover on a 2014 Cherokee KL. The creator states that it may fit additional KL model years, but this entry makes no broader claim.

No-drill bracket that relocates the factory off-road accessory kit into the right cargo-side alcove of a 2017 Cherokee KL Trailhawk without the subwoofer. It engages the existing bag hooks and overlapping trim.

Drop-in cupholder adapter developed for a 2019 Cherokee KL to support a 26 oz Yeti Rambler that is too large for the factory cupholder.

Plain snap-in cover for an exposed roof-rail mounting opening on a 2014 Cherokee KL. This entry excludes the decorative grille and wordmark variants.

Left- and right-side replacement end clips for the Mopar cargo-shade cover in a 2019 Cherokee KL Trailhawk. The source notes an 8.8 mm shaft diameter and recommends a tougher material than PLA.

Replacement control knob for a missing power-window switch on a 1997 Grand Cherokee ZJ. The creator iterated the fit and reports that the final geometry works correctly.

Replacement internal link that joins the driver-door window-switch button to its contact pins on a Grand Cherokee ZJ.

Replacement drive gear for a failed power-seat motion axis in a 1997 Grand Cherokee ZJ. The creator installed the printed gear after removing the broken original and documents the repaired mechanism.

Replacement push button for the exterior door-opening handle on a 1998 Grand Cherokee ZJ.

Threaded replacement hood-height stop measured from the original on a 1993 Grand Cherokee ZJ. The creator installed the part and recommends an under-hood material rather than PLA.

Replacement cupholder insert shaped for the Grand Cherokee ZJ center console.

Strengthened upper clip that retains the Grand Cherokee ZJ headlight reflector to its vertical adjuster. The source covers the full 1993–1998 ZJ range and documents the load-oriented print position.

Replacement transfer gear and pressure roller for the Grand Cherokee ZJ power-antenna drive. The creator installed the pair after the worn mechanism rattled and failed to extend fully.

Replacement roller for the scissor-type window regulator used in the Grand Cherokee ZJ. Three rollers service one regulator; the creator documents heat-assisted installation over the original ball-ended pins.

Replacement passenger-side interior release handle developed for a circa-1994 Grand Cherokee ZJ and installed in the vehicle. A heat-resistant cabin material and high infill are recommended.

Segmented inserts that replace the missing extruded-rubber strips in the stainless cargo-floor moldings of a Grand Cherokee ZJ. The segments are sized for a compact printer and conceal their joints after installation.

Blank replacement panel for the 1993–1998 Grand Cherokee ZJ Vehicle Information Center or Graphic Display Module opening. The panel provides a clean base for switches, gauges, or ports.

Radio fascia for adapting a single-DIN head unit to the factory radio opening in Grand Cherokee ZJ and export-model ZG dashboards. Locating pins reproduce the original mounting position.

Push-fit center cap modeled for 1993–1998 Grand Cherokee ZJ wheel hubs. The source includes an installed result and recommends PETG with supports.

Service funnel sized for the 19 mm automatic-transmission fill tube on a Grand Cherokee ZJ. Small sealing rings are included in the printed geometry.

Replacement headlight closure-panel lock ring modeled for a 1996 Grand Cherokee ZJ. The creator identifies possible use across the 1993–1998 generation.

Replacement sun-visor retaining clip designed and used on a Grand Cherokee ZJ after the factory clip failed.

Socket tool for removing the lower outer headlight adjuster on 1993–1998 Grand Cherokee ZJ assemblies.

Bolt-on bracket developed for mounting a three-inch auxiliary light above the front fender of a Grand Cherokee ZJ. The source documents the installed bracket from three angles.

Replacement square peg for the Grand Cherokee ZJ headlight-adjustment mechanism.

Rigid MOLLE/PALS panel for the 1996–1998 Grand Cherokee ZJ center console. Standard and no-spacer versions are included, with the installation sequence and finished use documented.

Replacement link between the HVAC blend-door actuator and lever on a 1998 Grand Cherokee ZJ.

Replacement strain-relief shell for the neutral-safety-switch electrical connector on a 1998 Grand Cherokee ZJ.

Replacement wing handle for the spare-tire retainer used in 1999–2004 Grand Cherokee WJ and WG cargo areas. The print captures a standard M10 × 1.5 hex nut.

Replacement wheel center cap for the Grand Cherokee WJ and WG. This entry uses the creator's rebuilt Fusion geometry rather than the heavier original scan mesh.

Replacement receptacle for the ball studs on 1999–2004 Grand Cherokee WJ and WG headlight housings. Three receptacles support each lamp while preserving adjustment movement.

Flexible replacement stop for the fuel-filler door on a Grand Cherokee WJ or WG.

Replacement interior hood-latch release handle developed for a 2001 Grand Cherokee WJ and WG after the factory handle broke.

Dashboard fascia blank for fitting a double-DIN radio to a Grand Cherokee WJ or export-model WG. The user cuts the final opening for the chosen head unit; the source documents the installed fit.

Replacement cupholder for Grand Cherokee WJ and WG center consoles. Moving the cup openings rearward adds a small forward storage pocket; the creator verified the fit in a 2004 vehicle.

Replacement pivot pin for the Grand Cherokee WJ and WG heater-core door mechanism. The source specifies solid horizontal printing for strength and alignment with the actuator motor.

Replacement diffuser modeled from the original under-hood service lamp on a Grand Cherokee WJ or WG.

Removable sizing sleeve for the oversized driver-side cup opening in a 2004 Grand Cherokee WJ or WG. It supports a standard 20-ounce drink bottle and was test-printed in PETG.

Two-piece replacement for the ashtray and accessory-socket panel in 1999–2004 Grand Cherokee WJ and WG center consoles. The layout supports five Carling switches, two seat-heater switches, and five accessory sockets while reusing the factory metal latches.

Repair insert for a failed P21W bulb socket in Grand Cherokee WJ and WG tail-lamp circuit boards. The source documents the replacement cartridge and wired installation.

Replacement sun-visor mounting clip for 1999–2004 Grand Cherokee WJ and WG interiors. The creator reports a perfect fit and provides the printable mesh alongside the original CAD.

Two-piece front-bumper retainer modeled from the fastener on a 2000 Grand Cherokee WJ. The creator verified the installed function and oriented the insert for layer strength.

Two-piece floor plug and hose fitting for the Grand Cherokee WJ and WG sunroof drain. The source documents installation with RTV or silicone sealing at the body joint.

Replacement fuse-puller tool stored at the Grand Cherokee WJ and WG fuse panel. The source documents both the factory storage position and the printed replacement.

Socket-style service wrench for the 74.5 mm, 14-flute oil-filter housing used by the 2007–2008 Grand Cherokee WK and WH with the 3.0L CRD diesel engine. The creator designed it from measured filter geometry and documented a physical test print.

Double-DIN radio mounting kit for 2008–2010 Grand Cherokee WK and WH dashboards. The creator leaves mounting holes undrilled for the chosen head unit and explicitly documents identical fitment in 2008–2010 Commander, 2008–2012 Liberty, and 2007–2017 Wrangler dashboards.

Replacement panel for the left-side dashboard cubby in 2008–2010 Grand Cherokee WK and WH interiors. The selected, creator-tested version holds five 20 mm round Hella H61923001-style switches; the untested square-hole variant is intentionally excluded.

Flexible replacement escutcheon for the fixed fender antenna on Grand Cherokee WK and WH vehicles. Two bore sizes are supplied for installation with a 21 mm outer-diameter, 14.5 mm inner-diameter sealing washer.

Replacement driver-side lock and unlock rocker for 2005–2010 Grand Cherokee WK and WH door-switch panels. It reuses the original spring and metal spring cap; the creator reverse-engineered and tested it from the failed factory button.

Two-piece housing that replaces the cigarette-lighter socket in a 2005 Grand Cherokee WK or WH and secures the USB extension from an aftermarket radio. The creator reports the assembly working in the vehicle.

Replacement outer cover for the front-passenger seat-belt anchor on a 2008 Grand Cherokee WK or WH. The source includes the factory part, printed geometry, and physical fit views.

Replacement trim retainer modeled from the surviving clip on a 2007 Grand Cherokee WK or WH. The creator printed it in PETG, installed it, and reports that it remained secure for several months.

Two-piece snap-together replacement eyelet for the cargo-floor tie-down points in a Grand Cherokee WK or WH.

Replacement drive gear for the power-adjustable accelerator-pedal mechanism in a Grand Cherokee WK or WH. The creator printed it solid in PETG, lubricated the thread, installed it, and reports restored adjustment.

Replacement sun-visor support bracket for 2005–2010 export Grand Cherokee WH and corresponding WK interiors. The source provides the finished physical print and matching CAD geometry.

Flexible replacement dust cover for the automatic shifter gate in 2005–2010 Grand Cherokee WK and WH center consoles. The creator documents the installed fit and specifies NinjaFlex.

Protective fitted sleeve for the key fob used with 2014 and 2016 Grand Cherokee WK2 vehicles. The creator documents the physical print around the complete fob.

Replacement internal gear for the air-conditioning actuator in a 2011 Grand Cherokee WK2. The printable geometry reproduces the failed compound gear and keyed center bore.