3D-printable parts for your Jeep.
The parts registry for Jeep trucks and 4x4s.
A community registry of replacement parts, brackets, knobs, and trim pieces for Wrangler YJ through JL, Cherokee, Grand Cherokee, Gladiator, Comanche, and the CJ canon. Preview the model in your browser. Download the STL. Print at home.
- 01Free to take
Every STL is free. No paywalls, no premium tiers. Print at home or have a member print it for you.
- 02Proven on a truck
Each part on the registry has been fitted at least once. We're not a model gallery — we're a parts catalog.
- 03Open registry
Designed by enthusiasts, owned by no one. Cross-referenced to OEM part numbers where they exist.
Seat-Back MOLLE Panel Mount Set
Jeep Commander mounting set for attaching a compatible MOLLE organizer panel behind a front seat. The set includes the headrest bracket, lower connector, and retaining pin; M4 x 35 mm screws and 5 mm elastic cord complete the installation.
Roof-Antenna Trim Bezel
Replacement exterior trim bezel for the roof antenna on a Jeep Commander. The creator updated the geometry for fit and documents the broken original beside the printed replacement.
Rear-Seat Release-Lever Plug
Replacement actuator plug for the Jeep Commander rear-seat release lever. Without the plug the seat release does not operate; the printable geometry directly replaces the discontinued original component.
2007 Rear-HVAC Vent Hose Adapter
Adapter designed for the rear HVAC outlet in a 2007 Jeep Commander. It accepts 1-1/8-inch bilge/discharge hose to route air toward a rear child seat, and the source documents the installed setup.
2006 Shift-Knob Cap
Replacement cap for a missing automatic shifter-knob insert, designed to fit a 2006 Jeep Commander.
Front Wheel-Well Access Flap
Replacement access flap for the Jeep Commander front wheel-well liner. The source gallery documents the printed panel and its installation in the liner opening.
Rear-Camera Back Plate
Replacement back shell plate for the rear camera assembly on a Jeep Renegade.
Sun-Visor Socket Hinge
Replacement socket-hinge piece for a broken Jeep Renegade sun visor. The creator printed the working part in PETG and documents it installed.
Rear License-Plate Mount Extenders
Pair of rear license-plate mount extenders for securing a standard US Washington plate to all four sockets on a Jeep Renegade. Each accepts a press-fit M6 nut and uses short low-profile screws.
Power-Seat Drive Gear
Replacement drive gear for a failed power-seat motion axis in a 1997 Grand Cherokee ZJ. The creator installed the printed gear after removing the broken original and documents the repaired mechanism.
Dashboard Vent and Vane Set
Complete repair set for the missing or cracked center and side vents in a 2002 TJ, including housings, vanes, sliders and geared control pieces. The creator printed prototypes and specifies heat-resistant material for service use.
67 Designs Rail-Compatible Mount Set
Modular Wrangler JL dashboard-rail mounting set with heat-resistant printable bases, arms, 20 mm ball adapters, magnetic base, and left/right holders for 67 Designs-compatible rails.
Automatic-Shifter Dust Cover
Flexible replacement dust cover for the automatic shifter gate in 2005–2010 Grand Cherokee WK and WH center consoles. The creator documents the installed fit and specifies NinjaFlex.
Taillight Housing and Separator
Printable rear lamp housing with deeper lens-screw holes, a wiring opening and internal rails for the included red-and-clear lens separator. The source recommends heat-resistant material and provides both printable parts.
Sun-Visor Socket Hinge
Replacement socket-hinge piece for a broken Jeep Renegade sun visor. The creator printed the working part in PETG and documents it installed.
Cargo-Cover Support Extender
Press-fit extender for the Jeep Renegade rear luggage-cover support. It increases engagement so the cover does not fall when the opposite side is being hooked in place.
1996–1998 Center-Console MOLLE Panel
Rigid MOLLE/PALS panel for the 1996–1998 Grand Cherokee ZJ center console. Standard and no-spacer versions are included, with the installation sequence and finished use documented.
RENIX Hood-Prop Rod Holder
Replacement hood-prop rod holder for RENIX-era Cherokee XJ and Comanche MJ vehicles. The creator does not claim fitment on 1997–2001 Cherokees.
Submit it to the registry.
Measured a bracket on Fusion 360 last weekend that fixed your dash? Log it here so the next person doesn't have to redraw it. We review every submission before it ships, and you keep credit and licence.