Jeep Cherokee / Liberty XJ 3D-printable parts

Replacement end clip for broken mechanical heater-control cables. The creator verified it on 1991 controls and identifies select CJ, YJ and XJ applications; fit and cable travel should be checked before reassembly.

Adapter that fits a short, wide Toyota-pattern push switch into the factory Jeep switch panel. The creator specifies 1997–2004 Wrangler TJ and 1997–2001 Cherokee XJ applications.

Auxiliary switch panel for a 2000 Cherokee XJ that mounts ahead of the shifter with automotive double-sided tape. Single rectangular, three rectangular, and round-rocker layouts are included.

Solid replacement knob for the manual window crank on a 1993 Cherokee XJ. The creator omitted the weak pre-cut shaft opening so the crank pin forms its own tight fit during installation.

Slotted replacement for the failed plastic pivot in a Cherokee XJ electric door mirror. The slot lets the wiring pass through so the mirror does not need complete disassembly.

Removable twin cup holder for the rear of a 2001 Cherokee XJ center console. The armrest passes through the frame to retain it, and the cup inserts lift out for cleaning.

Twin cup holder shaped for the parking-brake area of a 1984–1996 Cherokee XJ center console.

Dashboard bracket for mounting an aftermarket single-DIN stereo in a 1997–2001 Cherokee XJ.

Small right-side lower trim replacement for a pre-facelift four-door Cherokee XJ, positioned between the passenger door and rear wheel arch. It is not intended for the two-door body.

Replacement bracket that supports the retractable cargo cover directly behind the rear seats of a Cherokee XJ.

Clear-print replacement lens for the rear cargo lamp in a pre-facelift Cherokee XJ. The creator notes that its edges are straight rather than curved like the original.

Glue-on repair bases for broken trim-clip mounts on the Cherokee XJ tailgate cover. Standard and short bases are included for the different factory positions.

Multi-piece left- and right-side replacement end caps for factory Cherokee XJ side steps. The sections are bonded after printing and the screw piece must be tapped before installation.

Two-piece puller for removing a seized AW4 automatic-transmission neutral-safety switch without prying on it. It uses an M8 nut and bolt to draw the switch from its shaft.

Replacement center-dash switch carrier for a 1997–2001 Cherokee XJ. It holds six factory-style switches plus one round 12-volt accessory socket.

Clip-on retainer that holds a broken rear washer nozzle together on a 1997–2001 Cherokee XJ wiper arm without adhesive.

Replacement rear hooks for the retractable privacy cover in a 1984–1996 Cherokee XJ cargo area. Original-position and 12 mm inboard left/right versions are included.

Plain push-fit center cap modeled for the approximately 64 mm stock wheel opening on a 1992 Cherokee XJ. This entry excludes the decorative lettered variant.

Clock-delete switch panel developed on a 1989 Comanche MJ and stated by the creator to fit the Cherokee XJ dashboard. Blank and pre-drilled switch layouts are included.

Replacement captive screw-nut insert for the Cherokee XJ front grille. The creator recommends PETG or ABS for service temperature and durability.

Replacement retaining bracket for the Cherokee XJ cargo area, designed to print on its side with support.

Replacement sun-visor retaining clip modeled for an 1980s Cherokee XJ. The creator used PETG for the installed parts.

Replacement hood-prop rod holder for RENIX-era Cherokee XJ and Comanche MJ vehicles. The creator does not claim fitment on 1997–2001 Cherokees.

Taller replacement button for a Cherokee XJ roof-rack rail. The revised height and outer-face recess correct rocking seen with the earlier geometry.

Plain center cap sized for the 16-inch ICON wheels on a 2001 Cherokee XJ Classic. Confirm the wheel opening before printing for a different stock wheel.

Drop-in storage pocket that replaces the ashtray in a Cherokee XJ center dashboard.

Reinforced replacement for the failure-prone automatic-transmission selector insert in a 1997–2001 Cherokee XJ. This entry uses the creator's final second revision.

Flexible replacement stop for a Cherokee XJ glovebox. The creator printed it in TPU to reproduce the original rubber function.

Door-corner pod for installing the creator's specified aftermarket tweeter in a 1997–2001 Cherokee XJ. Confirm tweeter diameter before printing.

Load-spreading washer that repairs broken dashboard material around the headlight switch on a 1984–1996 Cherokee XJ. Its diameter can be scaled for a larger damaged area.

Adapter bracket used on a 1999 Cherokee XJ to cover the original rear mounting holes while attaching a European-format license-plate holder.

Simple spacer used to retain a replacement blower motor in a Cherokee XJ heater housing.

Center-dash panel for installing two round 12-volt accessory sockets in a Cherokee XJ.

No-drill rain-gutter bracket for mounting small side floodlights on a 2001 Cherokee XJ. The latest hooked, hex-head V5 geometry is included.

Adapter ring for mounting Hertz X130-size replacement speakers in the rear roof positions of a 1997–2001 Cherokee XJ with the Infinity system.

Replacement transfer-case shift-indicator plate and insert for the floor console used in Cherokee XJ and Comanche MJ vehicles. The blank surface can be lettered or backlit.

Driver- and passenger-side replacement mirror mounts for 1984–1996 Cherokee XJ doors. Easy slotted and full replacement versions support manual or electric mirrors.

Replacement roof-rack rail stanchion buttons for the 1996 curved and 2000 Cherokee XJ profiles.

Replacement clip that stows the hood support rod on a 1989 Cherokee XJ.

Direct replacement windshield-washer nozzle for a 1989 Cherokee XJ, revised with three spray ports and reinforced hose-barb and mounting joints.

Replacement exterior antenna mounting flange for a 1989 Cherokee XJ. The creator notes that its outside diameter is smaller than the original.

Glue-on replacement anchor for broken rear-hatch trim mounting points on a 1989 Cherokee XJ. The source describes reinforced epoxy bonding to the remaining plastic.

Replacement shim for a missing rear-seat hinge pin isolator on a 1989 Cherokee XJ.

Removable collar and flat-bottom insert that stabilize smaller cups in the rear cupholder of a 1997–2001 Cherokee XJ center console.

Switch plate for the ashtray opening in a 2000 Cherokee XJ. Functional five-hole and blank versions are included

Clamp-style mount for adding a gauge to a Cherokee XJ steering column without drilling the column trim.

Clock-delete panel for a Cherokee XJ or Comanche MJ dashboard that accepts one 52 mm gauge and two rocker switches.

Three-inch plug for the large driver- and passenger-side front floor openings in a 1984–1996 Cherokee XJ. Fitment on 1997–2001 vehicles is not claimed.

Replacement latch for the center-console lid on a 1997–2001 Cherokee XJ. The source recommends an angled print orientation to improve strength.

Flexible sealing plug for the interior body antenna pass-through on a 1995 Cherokee XJ. This is not the exterior fender-top plug.

Replacement latch for the center-console lid on a 1984–1996 Cherokee XJ, with an orientation guide for improved layer strength.

Press-fit dashboard mount measured for an Auxbeam six-gang controller in a 1998 Cherokee XJ. The creator states that the first release had not yet been test-fitted.

Replacement trim bezel around the front-seat folding lever in a two-door Cherokee XJ. The same geometry fits either seat side.

Removable storage bin and lid for the small rear cupholder in a Cherokee XJ center console.

Dimensionally matched replacement blank for unused dashboard switch openings in 1984–1996 Cherokee XJ and Comanche MJ interiors.

Oval firewall grommet for the 4.0L engine-control harness in 1984–1996 Cherokee XJ and Comanche MJ vehicles. Print in a suitable flexible, heat-resistant material.

Solid replacement cap for the engine-bay relay cover used on 1984–1996 Cherokee XJ and Comanche MJ vehicles. Use a high-temperature material.

Replacement center-vent body that holds a 52 mm auxiliary gauge in a Cherokee XJ dashboard.

Replacement sliding cover for the Cherokee XJ automatic gear selector. The reinforced face installs downward and the creator recommends semi-flexible filament.

Purpose-built wrench for removing a seized Cherokee XJ fuel-pump retaining ring without striking the ring with a hammer and screwdriver.

Replacement slotted insert modeled from a surviving 1997–2001 Cherokee XJ grille insert. The creator recommends minor scaling if required for the individual grille.

Replacement dashboard bezel for mounting a single-DIN radio in a Cherokee XJ. It is oriented to fit a 220 × 220 mm print bed.