Jeep Cherokee / Liberty 3D-printable parts

Replacement louvre linkage arm and five blade profiles for repairing the dashboard air vents in a 2005 Jeep Liberty KJ. The submitted meshes preserve the source geometry while reducing excessive tessellation for the API.

Replacement end clip for broken mechanical heater-control cables. The creator verified it on 1991 controls and identifies select CJ, YJ and XJ applications; fit and cable travel should be checked before reassembly.

Taller replacement button for a Cherokee XJ roof-rack rail. The revised height and outer-face recess correct rocking seen with the earlier geometry.

Replacement hood-prop rod holder for RENIX-era Cherokee XJ and Comanche MJ vehicles. The creator does not claim fitment on 1997–2001 Cherokees.

Two-piece puller for removing a seized AW4 automatic-transmission neutral-safety switch without prying on it. It uses an M8 nut and bolt to draw the switch from its shaft.

Switch plate for the ashtray opening in a 2000 Cherokee XJ. Functional five-hole and blank versions are included

Replacement transfer-case shift-indicator plate and insert for the floor console used in Cherokee XJ and Comanche MJ vehicles. The blank surface can be lettered or backlit.

Replacement internal gear for a clicking HVAC blend-door actuator in a 2010 Jeep Liberty KK. The creator installed the printed gear and reports that the actuator operates.

Reinforced replacement sun-visor clip for a Jeep Liberty KJ. This revision adds a small retention bump so the visor clicks securely into the clip.

Replacement center fin for a broken dashboard air vent in a 2003 Jeep Liberty KJ. The creator notes that the end pins may require light sanding for fit.

Multi-piece snap-in center cap modeled for the approximately 55–56 mm wheel opening on a 2004 Jeep Liberty KJ. This entry uses the creator's plain top and excludes the decorative lettered top.

Replacement brackets and spacers that support the pop-up air dam on the sliding Sun-Rider roof fitted to a Jeep Liberty KJ. The creator modeled them from the original parts and used the printed set successfully.

Replacement latch for the center-console lid on a 1984–1996 Cherokee XJ, with an orientation guide for improved layer strength.

Direct replacement windshield-washer nozzle for a 1989 Cherokee XJ, revised with three spray ports and reinforced hose-barb and mounting joints.

Double-DIN radio mounting kit for 2008–2010 Grand Cherokee WK and WH dashboards. The creator leaves mounting holes undrilled for the chosen head unit and explicitly documents identical fitment in 2008–2010 Commander, 2008–2012 Liberty, and 2007–2017 Wrangler dashboards.

Left- and right-side replacement end clips for the Mopar cargo-shade cover in a 2019 Cherokee KL Trailhawk. The source notes an 8.8 mm shaft diameter and recommends a tougher material than PLA.

Plain snap-in cover for an exposed roof-rail mounting opening on a 2014 Cherokee KL. This entry excludes the decorative grille and wordmark variants.

Drop-in cupholder adapter developed for a 2019 Cherokee KL to support a 26 oz Yeti Rambler that is too large for the factory cupholder.

No-drill bracket that relocates the factory off-road accessory kit into the right cargo-side alcove of a 2017 Cherokee KL Trailhawk without the subwoofer. It engages the existing bag hooks and overlapping trim.

Replacement retaining clip for the headlight and fog-lamp service access cover on a 2014 Cherokee KL. The creator states that it may fit additional KL model years, but this entry makes no broader claim.

Coin organizer shaped for the lower-right dashboard panel in a 2011 Jeep Liberty KK. It mounts with automotive trim tape after cleaning the panel.

Shorter replacement radio antenna developed for a 2008 Jeep Liberty KK to clear a garage door. Plain and captured-nut bases, the wire support, and weather radome are included; assembly requires an M5 fastener and antenna wire.

Hand tool for releasing the fuel-line quick connector on a 2005 Cherokee KJ or Liberty KJ.

Dashboard pod for two auxiliary gauges in a Cherokee KJ or Liberty KJ. It fits without drilling or cutting the instrument panel.