Jeep Wrangler JK 3D-printable parts

Low-profile fog-light mount for a Wrangler JK aftermarket bumper where a winch interferes with the factory cup. It moves the original fog lamp forward approximately 13 mm.

Holder for a 14 mm aftermarket hands-free microphone in the factory UConnect microphone position of a Wrangler JK. Rounded and squared holder variants are included.

Outer bushing that fits a Hi-Lift jack climber rung around the Rampage carrier bolt to suppress rattling. The creator states JK and JL fitment.

Printable hand knob assembly for Wrangler JK Freedom-panel bolts. It captures an M8 × 1.25 × 75 mm bolt for tool-free panel retention.

Right-hand passenger sun-visor pivot mount modeled after the broken mount in a Wrangler JK. It allows repair without replacing the complete visor assembly.

Replacement climate-control knob shell modeled for a 2010 Wrangler JK dashboard. Confirm shaft fit before pressing it fully into place.

Auxiliary round-rocker switch panel shaped to the curved radio bezel used on 2011–2018 Wrangler JK and JKU interiors. Installation requires holes behind the panel.

Clip-in defrost-air diverter for 2007–2010 Wrangler JK dashboards. It redirects air from the short factory grille toward the outer windshield edges.

Double-DIN radio mounting kit for 2008–2010 Grand Cherokee WK and WH dashboards. The creator leaves mounting holes undrilled for the chosen head unit and explicitly documents identical fitment in 2008–2010 Commander, 2008–2012 Liberty, and 2007–2017 Wrangler dashboards.

Inner bushing for the Rampage Hi-Lift jack carrier that limits fore-and-aft movement of its horizontal carry bolt and reduces rattling. The creator states JK and JL fitment.

Replacement raised-number insert for the automatic shifter knob in a Wrangler JK.

Replacement cylindrical roller for the Wrangler JK sun visor. It restores a firm grip in the visor clip so the visor stays stowed, including during off-road use.

Three-piece flexible replacement tether for the Wrangler JK fuel cap. The pins are intentionally snug and may be warmed slightly for assembly.

Printable floor drain plug stated by the creator to fit Wrangler JK, Wrangler JL, and Gladiator JT floors and compatible drain openings in their floor mats. This entry contains only the functional plug body.

Push-fit center cap for Wrangler JK steel wheels with an approximately 65 mm center bore and 84 mm outer face. This entry uses the creator's plain, no-logo geometry.

Replacement bracket for the factory subwoofer enclosure in a Wrangler JK. It substitutes for the original metal piece when corrosion has damaged it.

Flexible replacement mounting grommet for the engine appearance cover on approximately 2012–2016 Wrangler JK models.

Snap-fit replacement cap for the automatic shifter knob in a Wrangler JK. The model is designed to retain like the original cap; a small amount of removable hot glue can add security.

Replacement arrow-head retaining clip modeled from the Wrangler JK rear fender-flare fastener. Print in a strong, heat-resistant material with controlled flex.

Large spiked washer that spreads the load of the factory 10 mm heat-shield fastener on a Wrangler JK subframe. The creator specifies solid, high-temperature tough material and used glass-filled nylon; sandwich it under a metal washer.

Factory-style under-hood switch panel for a Wrangler JK fitted with an ARB Twin compressor. Versions with and without a reinforced quick-connect air-chuck opening are included.

Drop-in organizer for the small console recess ahead of the automatic shifter in a 2010 Wrangler JK or JKU. It provides coin slots and a cylindrical holder.

One-piece rigid replacement for a torn Wrangler JK front-door mesh pocket. Mirror the model in the slicer for the opposite door.

Extender that restores contact between the Wrangler JK tailgate bump stop and a spare tire after fitting offset aftermarket wheels. It accepts the original bump stop and an added rubber isolator.