Jeep Wrangler JL 3D-printable parts

Modular Wrangler JL dashboard-rail mounting set with heat-resistant printable bases, arms, 20 mm ball adapters, magnetic base, and left/right holders for 67 Designs-compatible rails.

Outer bushing that fits a Hi-Lift jack climber rung around the Rampage carrier bolt to suppress rattling. The creator states JK and JL fitment.

Two-piece six-switch panel that replaces the right-side media-center trim in Wrangler JL and Gladiator JT dashboards. The rear plate and switch retaining nuts clamp the assembly around the factory opening.

Two-piece dashboard-pocket mount for a Yaesu FTM-500 control head in Wrangler JL and Gladiator JT vehicles. It requires no vehicle drilling and the source documents the installed assembly from three angles.

Compact replacement housing for Wrangler JL and Gladiator JT key-fob electronics, factory buttons, battery, and screws. The selected revision-four top and bottom incorporate the creator's fit and stiffness updates.

Two-piece protective shell for Wrangler JL and Gladiator JT key fobs. The bolted enclosure shields the panic button from accidental pocket presses while retaining access to the normal controls.

Vehicle-specific dashboard-pocket mount for the ICOM IC-7100 control head in Wrangler JL and Gladiator JT interiors. The source documents several weeks of installed use and uses removable hook-and-loop fastening.

Nonconductive bracket for a Warn winch power-interrupt solenoid in the Gladiator JT engine bay. It uses an otherwise unused passenger-side body hole with an M6 rivnut; the creator also reports confirmed fitment from Wrangler JL and JLU owners.

Snap-on flashlight holder for the factory front-seat track in Wrangler JL and Gladiator JT vehicles. It installs without drilling and the source documents both the printed clamp and its physical fit.

Single auxiliary-light bracket for the cowl or lower A-pillar mounting area of a Wrangler JL.

Blank and left/right RJ45 faceplates for the Wrangler JL Rubicon left dashboard cubby. The connector openings fit extensions used with Midland MXT275 and MXT575 radio handsets.

Engine-bay bracket for mounting a Garmin PowerSwitch and an adjacent winch relay in a Wrangler JL.

Reinforcement plate for the failure-prone Wrangler JL sun-visor pivot. This revised remix adds beveled screw holes, tapered ends, and locating extrusions in the original holes.

Eight-millimeter gauges used when manually calibrating Freedom-panel position on Wrangler JL, JLU, and Gladiator JT roofs.

Tool-free magnetic holder for a Tazer JL Mini module under the dashboard of Wrangler JL or Gladiator JT models. It uses five 12 by 3 mm magnets and leaves the status light and USB port accessible.

Bumper adapter for installing a three-inch pod light in a Wrangler JL fog-light opening. The creator reports successful use and recommends ABS, PETG, or ASA.

Updated airflow-control plugs for the Wrangler JL dashboard defroster grille. The creator recommends ASA for cabin heat and UV stability.

A-pillar mount with two 20 mm accessory balls for Wrangler JL and Gladiator JT. It reuses the factory pillar bolt with a smaller replacement washer.

Friction-fit blank faceplate for the left dashboard cubby on 2018–2021 Wrangler JL models equipped with factory auxiliary switches.

Press-fit removable cover for the exposed door-lock keyhole on Wrangler JL and JLU models.

Insert used in pairs to fill the license-plate mounting holes in an AEV rear bumper before the plate screws are installed on a Wrangler JL.

Friction-fit auxiliary switch panel for 2018-and-newer Wrangler JL models without power windows. It accepts four 19 mm round switches and one rocker switch.

Service tool for removing a stubborn Wrangler JL wiper arm before folding the windshield. It uses a standard 1/4-inch bolt and nut.

Printable W-type retaining clip sized for the fender-flare slots on 2018-and-newer Wrangler JL and compatible Gladiator JT applications. This entry uses the creator's support-free revision.