Exterior — 3D-printable Jeep parts

Printable rear lamp housing with deeper lens-screw holes, a wiring opening and internal rails for the included red-and-clear lens separator. The source recommends heat-resistant material and provides both printable parts.

Two-piece front-bumper retainer modeled from the fastener on a 2000 Grand Cherokee WJ. The creator verified the installed function and oriented the insert for layer strength.

Replacement square peg for the Grand Cherokee ZJ headlight-adjustment mechanism.

Taller replacement button for a Cherokee XJ roof-rack rail. The revised height and outer-face recess correct rocking seen with the earlier geometry.

Replacement hood-prop rod holder for RENIX-era Cherokee XJ and Comanche MJ vehicles. The creator does not claim fitment on 1997–2001 Cherokees.

Printable rectangular taillight lens for the standard late-CJ and YJ rear lamp housing. The creator printed it in clear ABS for use with red and white LED bulbs.

Two-piece replacement windshield hold-down knob for a 1981 Jeep CJ-7. A three-eighths-inch fastener is inserted into the printed knob and retained by the separate tapered cap.

Pair of front license-plate brackets for a 2015 Grand Cherokee WK2 lower grille. Each bracket accepts a plate screw and fastens to the mesh with a zip tie, avoiding drilled holes; the creator documents the exact mounting location.

Replacement receptacle for the ball studs on 1999–2004 Grand Cherokee WJ and WG headlight housings. Three receptacles support each lamp while preserving adjustment movement.

Replacement headlight closure-panel lock ring modeled for a 1996 Grand Cherokee ZJ. The creator identifies possible use across the 1993–1998 generation.

Replacement transfer gear and pressure roller for the Grand Cherokee ZJ power-antenna drive. The creator installed the pair after the worn mechanism rattled and failed to extend fully.

Strengthened upper clip that retains the Grand Cherokee ZJ headlight reflector to its vertical adjuster. The source covers the full 1993–1998 ZJ range and documents the load-oriented print position.

Replacement transfer-case shift-indicator plate and insert for the floor console used in Cherokee XJ and Comanche MJ vehicles. The blank surface can be lettered or backlit.

Low-profile fog-light mount for a Wrangler JK aftermarket bumper where a winch interferes with the factory cup. It moves the original fog lamp forward approximately 13 mm.

Cupholder that uses the stock windshield-mount-plate holes on late CJ and YJ vehicles without the factory dash pad. It is sized for a mug with a carabiner handle and the creator test-fitted a PETG print.

Snap-in plug for a flat one-inch floor drain hole. The source warns that a hole crossing a floor bend may need a slightly smaller plug.

Adapter for fitting an older Omix-Ada 11020.01-style rear-view mirror to the newer windshield frame in a 1981 Jeep CJ-7. The source documents the printed adapter and physical installation.

Three factory-style windshield hood-block geometries measured from original parts and Willys master-parts documentation. Separate printable blocks cover CJ-2A, CJ-3A, and CJ-3B vehicles; two matching blocks are required per Jeep.

Repair insert for a failed P21W bulb socket in Grand Cherokee WJ and WG tail-lamp circuit boards. The source documents the replacement cartridge and wired installation.

Replacement diffuser modeled from the original under-hood service lamp on a Grand Cherokee WJ or WG.

Replacement wing handle for the spare-tire retainer used in 1999–2004 Grand Cherokee WJ and WG cargo areas. The print captures a standard M10 × 1.5 hex nut.

Bolt-on bracket developed for mounting a three-inch auxiliary light above the front fender of a Grand Cherokee ZJ. The source documents the installed bracket from three angles.

Push-fit center cap modeled for 1993–1998 Grand Cherokee ZJ wheel hubs. The source includes an installed result and recommends PETG with supports.

Threaded replacement hood-height stop measured from the original on a 1993 Grand Cherokee ZJ. The creator installed the part and recommends an under-hood material rather than PLA.