Interior — 3D-printable Jeep parts

Complete repair set for the missing or cracked center and side vents in a 2002 TJ, including housings, vanes, sliders and geared control pieces. The creator printed prototypes and specifies heat-resistant material for service use.

Modular Wrangler JL dashboard-rail mounting set with heat-resistant printable bases, arms, 20 mm ball adapters, magnetic base, and left/right holders for 67 Designs-compatible rails.

Dashboard fascia blank for fitting a double-DIN radio to a Grand Cherokee WJ or export-model WG. The user cuts the final opening for the chosen head unit; the source documents the installed fit.

Switch plate for the ashtray opening in a 2000 Cherokee XJ. Functional five-hole and blank versions are included

Holder for a 14 mm aftermarket hands-free microphone in the factory UConnect microphone position of a Wrangler JK. Rounded and squared holder variants are included.

Replacement interior hood-latch release handle developed for a 2001 Grand Cherokee WJ and WG after the factory handle broke.

Replacement strain-relief shell for the neutral-safety-switch electrical connector on a 1998 Grand Cherokee ZJ.

Replacement link between the HVAC blend-door actuator and lever on a 1998 Grand Cherokee ZJ.

Radio fascia for adapting a single-DIN head unit to the factory radio opening in Grand Cherokee ZJ and export-model ZG dashboards. Locating pins reproduce the original mounting position.

Blank replacement panel for the 1993–1998 Grand Cherokee ZJ Vehicle Information Center or Graphic Display Module opening. The panel provides a clean base for switches, gauges, or ports.

Replacement internal link that joins the driver-door window-switch button to its contact pins on a Grand Cherokee ZJ.

Replacement control knob for a missing power-window switch on a 1997 Grand Cherokee ZJ. The creator iterated the fit and reports that the final geometry works correctly.

Replacement internal gear for a clicking HVAC blend-door actuator in a 2010 Jeep Liberty KK. The creator installed the printed gear and reports that the actuator operates.

Replacement climate-control knob shell modeled for a 2010 Wrangler JK dashboard. Confirm shaft fit before pressing it fully into place.

Auxiliary round-rocker switch panel shaped to the curved radio bezel used on 2011–2018 Wrangler JK and JKU interiors. Installation requires holes behind the panel.

Clip-in defrost-air diverter for 2007–2010 Wrangler JK dashboards. It redirects air from the short factory grille toward the outer windshield edges.

Adapter designed for the rear HVAC outlet in a 2007 Jeep Commander. It accepts 1-1/8-inch bilge/discharge hose to route air toward a rear child seat, and the source documents the installed setup.

Rear HVAC vent manifold and guide for the second-generation Jeep Compass. It installs behind the center-console vent trim and accepts one-inch corrugated hose to route air toward rear child seats; M2 fasteners secure the guides and clamps.

Under-dash bracket for a Nilight five-gang rocker-switch panel in a Jeep CJ-7. The source shows the installed panel and recommends heat-tapping the printed screw holes.

Two-piece steering-column cover for a CJ-7 converted to a Wrangler YJ tilt column. The right half includes a tachometer-wire clearance opening and threaded fastener points.

Speaker spacer rings developed while rebuilding a CJ-7 dashboard. They move replacement speakers away from the steel dash just enough for protruding tweeters to clear and are documented against the physical speaker assembly.

Two-piece snap-together breather vent for the hose ends on CJ-7 front and rear axles or the transfer case. The creator made it as a direct replacement and documents the assembled vent and installed hose fit.

Two-piece storage box for covering an oversized aftermarket-radio opening cut into a 1981 CJ-7 dashboard. Tabbed and plain halves glue together and convert the damaged opening into a useful cubby.

Replacement pull knob for the air, temperature, or defroster cable controls used in Jeep CJ-5 and CJ-7 dashboards. The creator developed it after the factory temperature knob broke and reports the current geometry working.