Interior — 3D-printable Jeep parts

Replacement end clip for broken mechanical heater-control cables. The creator verified it on 1991 controls and identifies select CJ, YJ and XJ applications; fit and cable travel should be checked before reassembly.

Replacement clip that retains a door latch push rod. It was modelled from an intact original and the creator reports that it clipped correctly into the door.

Three-piece replacement cupholder with a 3.5-inch front pocket, a 1.91-inch rear pocket and a separate base that can be glued or screwed in place.

Screw-on T-handle replacement for the parking-brake release control. The physical source photographs show the printed handle fitted below the dashboard.

Close factory-style replacement for the rotary heater and air-conditioning blower knob, modelled directly from a 1991 control.

Modular enclosures for 5.25-inch speakers that clamp around a 58 mm roll bar using M4 hardware. Sealed, accessory-port and left/right variants are included, and the creator reports the installed system fits and works.

Bracket for relocating a winch-controller jack into a grille slot. Exact grille spacing should be checked before drilling or wiring; speculative CJ and TJ fitment was not assigned.

Rear-seat cupholder that slides into the factory soft-top track and is retained by an existing track screw. The creator recommends high infill around the mounting tabs and upright.

Replacement door-hinge liners with separate early, later and driver-side printable variants. Source naming and year-marked files support late CJ, YJ and TJ applications.

Driver- and passenger-side replacement handles for paddle-style doors. The creator tested the design in a 1981 CJ-7 and states YJ and TJ compatibility, while warning that earlier non-paddle doors differ.

Replacement slider knob for the defrost, heater and vent controls. It was measured from a broken original, physically compared with the original and test-fitted successfully.

Close replica of the factory dashboard switch plate with openings for three standard toggle switches. The creator printed and installed the panel in PETG.

Cupholder that uses the stock windshield-mount-plate holes on late CJ and YJ vehicles without the factory dash pad. It is sized for a mug with a carabiner handle and the creator test-fitted a PETG print.

Two printable plastic spacer components for repairing the horn-button assembly. The source only verifies the YJ application, so other same-era vehicles were not linked.

Slip-on clip that holds the door courtesy-light switch open so the interior lights remain off when the doors are removed. It was designed around the pictured replacement switch.

Separate circular and rectangular flexible liners that replace the original rubber center-console insert without print supports. The physical photograph documents the original one-piece texture and layout.

Replacement lower bracket for the automatic-transmission shift-indicator assembly used across the 1997–2006 Wrangler TJ. The printed bracket accepts the original upper cover and hardware.

Exact-replica replacement foot for the removable rear bench seat, modeled from the part in a 2000 Wrangler Sport and designed to reuse the original embedded washer and screw.

Three-piece wall-mount system that supports removed TJ doors from their factory hinge points instead of the window frame. The creator printed and load-tested the PETG design.

Replacement bushing that removes play from the tilting passenger-seat slide mechanism on the 2002 Wrangler TJ.

Adapter that fits a short, wide Toyota-pattern push switch into the factory Jeep switch panel. The creator specifies 1997–2004 Wrangler TJ and 1997–2001 Cherokee XJ applications.

Hinged hook sized around the TJ's approximately three-inch padded roll bar. The revised left and right halves add a lower M3 closure to prevent spreading when unloaded.

Protective clips that snap over the lower edges of removed TJ doors before they are set on concrete or sand.

Left and right faceplates and enclosures that replace the TJ's front dashboard speaker mounts with 5.25-inch pods. The creator printed, installed and evaluated the complete set.

Snap-in blanks for the 2001 TJ center-console switch opening, supplied as a plain filler and a version for a common round rocker switch.

Adapter ring that mounts a 6.5-inch speaker in the factory TJ speaker pod without modifying the pod, using the original vehicle hardware and four M3 speaker screws.

Snap-in replacement bracket that secures the manual-transmission shifter boot to the TJ center console, modeled from the broken original and test-fitted in PETG.

Large-drink cupholder that bolts to the rear seat-mount area. The creator explicitly identifies and photographed TJ and JK fitment.

Replacement geared and plain internal flaps for a TJ dashboard vent that can no longer close.

Full replacement interior release handle modeled after the TJ original. The creator installed the design and reported it still working after approximately nine months.

OEM-shaped replacement rotary heater and air-conditioning control knob for 1999–2001 Wrangler TJ dashboards, measured from original controls and physically installed by the creator.

OEM-shaped replacement heater-control knob for the 1997 Wrangler TJ, measured from an original control and physically installed by the creator.

Springless replacement for the failure-prone upper soft-door window latch, measured from the factory part and installed on the creator's Wrangler.

Tight-fitting flexible replacement end for a TJ sun visor pivot.

Replacement rotary air-conditioning control knob for the 2006 Wrangler TJ, including a small hole for a contrasting filament position marker.

Drop-in organizer tray for the upper center console of a 1997 TJ, designed to print without supports and test-fitted by the creator.

Two-piece replacement visor clip with a push latch: lift the latch to release the visor and press it down to lock the visor in place.

Tested replacement fan-control knob for the 2004 Wrangler TJ, designed to reuse the metal insert from the broken original.

Replacement treble and bass adjustment button for the stock TJ radio.

Paired adapter nuts that allow Mercedes-pattern door-jamb switches to replace the TJ switches on both sides.

Clamp-style repair for a broken early-TJ temperature-control cable end, modeled and installed on a 1997 Wrangler.

Complete repair set for the missing or cracked center and side vents in a 2002 TJ, including housings, vanes, sliders and geared control pieces. The creator printed prototypes and specifies heat-resistant material for service use.

Clip-in defrost-air diverter for 2007–2010 Wrangler JK dashboards. It redirects air from the short factory grille toward the outer windshield edges.

Replacement carpet retaining clip for the Wrangler JK. The creator identifies six locations under the dash and seats where this printed fastener replaces a missing clip.

Auxiliary round-rocker switch panel shaped to the curved radio bezel used on 2011–2018 Wrangler JK and JKU interiors. Installation requires holes behind the panel.

A-pillar mounting post for a RAM-style arm in a Wrangler JK. The design installs with a 5/16-inch by 90 mm socket-head cap screw.

Replacement clip that secures the interior door-handle release cable on Wrangler JK doors. The creator recommends a heat-resistant, slightly flexible material.

One-piece rigid replacement for a torn Wrangler JK front-door mesh pocket. Mirror the model in the slicer for the opposite door.

Drop-in organizer for the small console recess ahead of the automatic shifter in a 2010 Wrangler JK or JKU. It provides coin slots and a cylindrical holder.

Holder for a 14 mm aftermarket hands-free microphone in the factory UConnect microphone position of a Wrangler JK. Rounded and squared holder variants are included.

Replacement climate-control knob shell modeled for a 2010 Wrangler JK dashboard. Confirm shaft fit before pressing it fully into place.

Snap-fit replacement cap for the automatic shifter knob in a Wrangler JK. The model is designed to retain like the original cap; a small amount of removable hot glue can add security.

Replacement bracket for the factory subwoofer enclosure in a Wrangler JK. It substitutes for the original metal piece when corrosion has damaged it.

Right-hand passenger sun-visor pivot mount modeled after the broken mount in a Wrangler JK. It allows repair without replacing the complete visor assembly.

Replacement cylindrical roller for the Wrangler JK sun visor. It restores a firm grip in the visor clip so the visor stays stowed, including during off-road use.

Replacement raised-number insert for the automatic shifter knob in a Wrangler JK.

Hook that holds the Wrangler JLU rear under-floor cargo hatch open by connecting its nylon loop to the child-seat anchor bar.

Flexible fitted liner for the factory cup-holder recess in a Wrangler JL center console.

Modular Wrangler JL dashboard-rail mounting set with heat-resistant printable bases, arms, 20 mm ball adapters, magnetic base, and left/right holders for 67 Designs-compatible rails.

Three-hole adapter ring for fitting a Kicker-style 4-inch replacement speaker in the factory Wrangler JL or Gladiator JT speaker location.

Two-piece Wrangler JL dash-camera mount that clamps at the rear-view mirror area and remains usable with the windshield folded. It assembles with an M4 fastener.

Clip-on CB radio microphone holder for the passenger grab handle in a Wrangler JL.

No-drill mount for a Midland MXTA25 low-profile antenna on the internal sport-bar fastener of a two-door 2018-and-newer Wrangler JL. The location is shared with soft-top hardware.

Friction-fit auxiliary switch panel for 2018-and-newer Wrangler JL models without power windows. It accepts four 19 mm round switches and one rocker switch.

Press-fit removable cover for the exposed door-lock keyhole on Wrangler JL and JLU models.

Friction-fit blank faceplate for the left dashboard cubby on 2018–2021 Wrangler JL models equipped with factory auxiliary switches.

A-pillar mount with two 20 mm accessory balls for Wrangler JL and Gladiator JT. It reuses the factory pillar bolt with a smaller replacement washer.

Updated airflow-control plugs for the Wrangler JL dashboard defroster grille. The creator recommends ASA for cabin heat and UV stability.

Tool-free magnetic holder for a Tazer JL Mini module under the dashboard of Wrangler JL or Gladiator JT models. It uses five 12 by 3 mm magnets and leaves the status light and USB port accessible.

Reinforcement plate for the failure-prone Wrangler JL sun-visor pivot. This revised remix adds beveled screw holes, tapered ends, and locating extrusions in the original holes.

Engine-bay bracket for mounting a Garmin PowerSwitch and an adjacent winch relay in a Wrangler JL.

Blank and left/right RJ45 faceplates for the Wrangler JL Rubicon left dashboard cubby. The connector openings fit extensions used with Midland MXT275 and MXT575 radio handsets.

Replacement door-speaker grille for full-size Jeep doors. The source photograph compares the printed grille with the surviving factory grille frame.

Auxiliary switch panel for a 2000 Cherokee XJ that mounts ahead of the shifter with automotive double-sided tape. Single rectangular, three rectangular, and round-rocker layouts are included.

Solid replacement knob for the manual window crank on a 1993 Cherokee XJ. The creator omitted the weak pre-cut shaft opening so the crank pin forms its own tight fit during installation.

Slotted replacement for the failed plastic pivot in a Cherokee XJ electric door mirror. The slot lets the wiring pass through so the mirror does not need complete disassembly.

Removable twin cup holder for the rear of a 2001 Cherokee XJ center console. The armrest passes through the frame to retain it, and the cup inserts lift out for cleaning.

Twin cup holder shaped for the parking-brake area of a 1984–1996 Cherokee XJ center console.

Dashboard bracket for mounting an aftermarket single-DIN stereo in a 1997–2001 Cherokee XJ.

Replacement bracket that supports the retractable cargo cover directly behind the rear seats of a Cherokee XJ.

Glue-on repair bases for broken trim-clip mounts on the Cherokee XJ tailgate cover. Standard and short bases are included for the different factory positions.

Replacement center-dash switch carrier for a 1997–2001 Cherokee XJ. It holds six factory-style switches plus one round 12-volt accessory socket.

Replacement rear hooks for the retractable privacy cover in a 1984–1996 Cherokee XJ cargo area. Original-position and 12 mm inboard left/right versions are included.

Clock-delete switch panel developed on a 1989 Comanche MJ and stated by the creator to fit the Cherokee XJ dashboard. Blank and pre-drilled switch layouts are included.

Replacement retaining bracket for the Cherokee XJ cargo area, designed to print on its side with support.

Replacement sun-visor retaining clip modeled for an 1980s Cherokee XJ. The creator used PETG for the installed parts.

Drop-in storage pocket that replaces the ashtray in a Cherokee XJ center dashboard.

Reinforced replacement for the failure-prone automatic-transmission selector insert in a 1997–2001 Cherokee XJ. This entry uses the creator's final second revision.

Flexible replacement stop for a Cherokee XJ glovebox. The creator printed it in TPU to reproduce the original rubber function.

Door-corner pod for installing the creator's specified aftermarket tweeter in a 1997–2001 Cherokee XJ. Confirm tweeter diameter before printing.

Load-spreading washer that repairs broken dashboard material around the headlight switch on a 1984–1996 Cherokee XJ. Its diameter can be scaled for a larger damaged area.

Simple spacer used to retain a replacement blower motor in a Cherokee XJ heater housing.

Center-dash panel for installing two round 12-volt accessory sockets in a Cherokee XJ.

Adapter ring for mounting Hertz X130-size replacement speakers in the rear roof positions of a 1997–2001 Cherokee XJ with the Infinity system.

Replacement transfer-case shift-indicator plate and insert for the floor console used in Cherokee XJ and Comanche MJ vehicles. The blank surface can be lettered or backlit.

Driver- and passenger-side replacement mirror mounts for 1984–1996 Cherokee XJ doors. Easy slotted and full replacement versions support manual or electric mirrors.

Glue-on replacement anchor for broken rear-hatch trim mounting points on a 1989 Cherokee XJ. The source describes reinforced epoxy bonding to the remaining plastic.

Replacement shim for a missing rear-seat hinge pin isolator on a 1989 Cherokee XJ.

Removable collar and flat-bottom insert that stabilize smaller cups in the rear cupholder of a 1997–2001 Cherokee XJ center console.

Switch plate for the ashtray opening in a 2000 Cherokee XJ. Functional five-hole and blank versions are included

Clamp-style mount for adding a gauge to a Cherokee XJ steering column without drilling the column trim.

Clock-delete panel for a Cherokee XJ or Comanche MJ dashboard that accepts one 52 mm gauge and two rocker switches.

Replacement latch for the center-console lid on a 1997–2001 Cherokee XJ. The source recommends an angled print orientation to improve strength.

Replacement latch for the center-console lid on a 1984–1996 Cherokee XJ, with an orientation guide for improved layer strength.

Press-fit dashboard mount measured for an Auxbeam six-gang controller in a 1998 Cherokee XJ. The creator states that the first release had not yet been test-fitted.

Replacement trim bezel around the front-seat folding lever in a two-door Cherokee XJ. The same geometry fits either seat side.

Removable storage bin and lid for the small rear cupholder in a Cherokee XJ center console.

Dimensionally matched replacement blank for unused dashboard switch openings in 1984–1996 Cherokee XJ and Comanche MJ interiors.

Replacement center-vent body that holds a 52 mm auxiliary gauge in a Cherokee XJ dashboard.

Replacement sliding cover for the Cherokee XJ automatic gear selector. The reinforced face installs downward and the creator recommends semi-flexible filament.

Replacement dashboard bezel for mounting a single-DIN radio in a Cherokee XJ. It is oriented to fit a 220 × 220 mm print bed.

Removable coin cup and riveted docking adapter shaped for the Jeep Liberty KJ center console. The cup is sized for US coins.

Replacement center fin for a broken dashboard air vent in a 2003 Jeep Liberty KJ. The creator notes that the end pins may require light sanding for fit.

Replacement rear cargo-area tie-down loop for a 2005 Jeep Liberty KJ, developed after the original riveted loop was damaged during carpet removal. The source includes installed validation photographs.

Replacement retaining clip for the windshield defrost vent in a Jeep Liberty KJ dashboard.

Replacement fader-control knob for the factory radio in a Jeep Liberty KJ. The creator recommends a heat-resistant material suitable for a parked vehicle interior.

Dashboard pod for two auxiliary gauges in a Cherokee KJ or Liberty KJ. It fits without drilling or cutting the instrument panel.

Reinforced replacement sun-visor clip for a Jeep Liberty KJ. This revision adds a small retention bump so the visor clicks securely into the clip.

Replacement louvre linkage arm and five blade profiles for repairing the dashboard air vents in a 2005 Jeep Liberty KJ. The submitted meshes preserve the source geometry while reducing excessive tessellation for the API.

Replacement internal gear for a clicking HVAC blend-door actuator in a 2010 Jeep Liberty KK. The creator installed the printed gear and reports that the actuator operates.

Coin organizer shaped for the lower-right dashboard panel in a 2011 Jeep Liberty KK. It mounts with automotive trim tape after cleaning the panel.

No-drill bracket that relocates the factory off-road accessory kit into the right cargo-side alcove of a 2017 Cherokee KL Trailhawk without the subwoofer. It engages the existing bag hooks and overlapping trim.

Drop-in cupholder adapter developed for a 2019 Cherokee KL to support a 26 oz Yeti Rambler that is too large for the factory cupholder.

Left- and right-side replacement end clips for the Mopar cargo-shade cover in a 2019 Cherokee KL Trailhawk. The source notes an 8.8 mm shaft diameter and recommends a tougher material than PLA.

Replacement control knob for a missing power-window switch on a 1997 Grand Cherokee ZJ. The creator iterated the fit and reports that the final geometry works correctly.

Replacement internal link that joins the driver-door window-switch button to its contact pins on a Grand Cherokee ZJ.

Replacement drive gear for a failed power-seat motion axis in a 1997 Grand Cherokee ZJ. The creator installed the printed gear after removing the broken original and documents the repaired mechanism.

Replacement push button for the exterior door-opening handle on a 1998 Grand Cherokee ZJ.

Replacement cupholder insert shaped for the Grand Cherokee ZJ center console.

Replacement transfer gear and pressure roller for the Grand Cherokee ZJ power-antenna drive. The creator installed the pair after the worn mechanism rattled and failed to extend fully.

Replacement roller for the scissor-type window regulator used in the Grand Cherokee ZJ. Three rollers service one regulator; the creator documents heat-assisted installation over the original ball-ended pins.

Replacement passenger-side interior release handle developed for a circa-1994 Grand Cherokee ZJ and installed in the vehicle. A heat-resistant cabin material and high infill are recommended.

Segmented inserts that replace the missing extruded-rubber strips in the stainless cargo-floor moldings of a Grand Cherokee ZJ. The segments are sized for a compact printer and conceal their joints after installation.

Blank replacement panel for the 1993–1998 Grand Cherokee ZJ Vehicle Information Center or Graphic Display Module opening. The panel provides a clean base for switches, gauges, or ports.

Radio fascia for adapting a single-DIN head unit to the factory radio opening in Grand Cherokee ZJ and export-model ZG dashboards. Locating pins reproduce the original mounting position.

Replacement sun-visor retaining clip designed and used on a Grand Cherokee ZJ after the factory clip failed.

Rigid MOLLE/PALS panel for the 1996–1998 Grand Cherokee ZJ center console. Standard and no-spacer versions are included, with the installation sequence and finished use documented.

Replacement link between the HVAC blend-door actuator and lever on a 1998 Grand Cherokee ZJ.

Replacement strain-relief shell for the neutral-safety-switch electrical connector on a 1998 Grand Cherokee ZJ.

Replacement wing handle for the spare-tire retainer used in 1999–2004 Grand Cherokee WJ and WG cargo areas. The print captures a standard M10 × 1.5 hex nut.

Replacement interior hood-latch release handle developed for a 2001 Grand Cherokee WJ and WG after the factory handle broke.

Dashboard fascia blank for fitting a double-DIN radio to a Grand Cherokee WJ or export-model WG. The user cuts the final opening for the chosen head unit; the source documents the installed fit.

Replacement cupholder for Grand Cherokee WJ and WG center consoles. Moving the cup openings rearward adds a small forward storage pocket; the creator verified the fit in a 2004 vehicle.

Replacement pivot pin for the Grand Cherokee WJ and WG heater-core door mechanism. The source specifies solid horizontal printing for strength and alignment with the actuator motor.

Removable sizing sleeve for the oversized driver-side cup opening in a 2004 Grand Cherokee WJ or WG. It supports a standard 20-ounce drink bottle and was test-printed in PETG.

Two-piece replacement for the ashtray and accessory-socket panel in 1999–2004 Grand Cherokee WJ and WG center consoles. The layout supports five Carling switches, two seat-heater switches, and five accessory sockets while reusing the factory metal latches.

Replacement sun-visor mounting clip for 1999–2004 Grand Cherokee WJ and WG interiors. The creator reports a perfect fit and provides the printable mesh alongside the original CAD.

Replacement fuse-puller tool stored at the Grand Cherokee WJ and WG fuse panel. The source documents both the factory storage position and the printed replacement.

Double-DIN radio mounting kit for 2008–2010 Grand Cherokee WK and WH dashboards. The creator leaves mounting holes undrilled for the chosen head unit and explicitly documents identical fitment in 2008–2010 Commander, 2008–2012 Liberty, and 2007–2017 Wrangler dashboards.

Replacement panel for the left-side dashboard cubby in 2008–2010 Grand Cherokee WK and WH interiors. The selected, creator-tested version holds five 20 mm round Hella H61923001-style switches; the untested square-hole variant is intentionally excluded.

Replacement driver-side lock and unlock rocker for 2005–2010 Grand Cherokee WK and WH door-switch panels. It reuses the original spring and metal spring cap; the creator reverse-engineered and tested it from the failed factory button.

Two-piece housing that replaces the cigarette-lighter socket in a 2005 Grand Cherokee WK or WH and secures the USB extension from an aftermarket radio. The creator reports the assembly working in the vehicle.

Replacement outer cover for the front-passenger seat-belt anchor on a 2008 Grand Cherokee WK or WH. The source includes the factory part, printed geometry, and physical fit views.

Two-piece snap-together replacement eyelet for the cargo-floor tie-down points in a Grand Cherokee WK or WH.

Replacement drive gear for the power-adjustable accelerator-pedal mechanism in a Grand Cherokee WK or WH. The creator printed it solid in PETG, lubricated the thread, installed it, and reports restored adjustment.

Replacement sun-visor support bracket for 2005–2010 export Grand Cherokee WH and corresponding WK interiors. The source provides the finished physical print and matching CAD geometry.

Flexible replacement dust cover for the automatic shifter gate in 2005–2010 Grand Cherokee WK and WH center consoles. The creator documents the installed fit and specifies NinjaFlex.

Protective fitted sleeve for the key fob used with 2014 and 2016 Grand Cherokee WK2 vehicles. The creator documents the physical print around the complete fob.

Replacement internal gear for the air-conditioning actuator in a 2011 Grand Cherokee WK2. The printable geometry reproduces the failed compound gear and keyed center bore.

Replacement cargo hook modeled for a 2013 Grand Cherokee WK2 luggage area.

Two-piece cross divider for the standard, non-locking center-console bin. The creator physically verified it in 2021 and 2022 Grand Cherokee consoles; the selected version 3 adds beveled lower corners and supersedes the hand-sanded version 2.

Replacement center-console storage bin for a 2019 Grand Cherokee WK2 without Selec-Terrain. It recesses and supports a REDARC trailer-brake remote knob without drilling the dashboard; the corrected revision 2 file is selected and the creator documents the installed assembly.

Protective ring for the power-seat lumbar switch used in 2011 and 2014 Grand Cherokee WK2 interiors. It prevents accidental adjustment while reaching into the vehicle and mounts around the existing control with double-sided tape.

Clip-on guard for the Selec-Terrain drive-mode control in 2011–2021 Grand Cherokee WK2 center consoles. It prevents pets or cargo from pressing the control while preserving intentional access.

No-drill mount for a REDARC trailer-brake controller knob in Grand Cherokee WL interiors. It reuses a trim screw below the steering wheel, preserves steering-column movement and knee clearance, and can be stabilized with double-sided tape.

Replacement blank cover for the media-center opening in a Jeep Gladiator JT center dashboard. The source shows the printed cover fitted beside the factory switch bank.

Snap-on flashlight holder for the factory front-seat track in Wrangler JL and Gladiator JT vehicles. It installs without drilling and the source documents both the printed clamp and its physical fit.

Nonconductive bracket for a Warn winch power-interrupt solenoid in the Gladiator JT engine bay. It uses an otherwise unused passenger-side body hole with an M6 rivnut; the creator also reports confirmed fitment from Wrangler JL and JLU owners.

Vehicle-specific dashboard-pocket mount for the ICOM IC-7100 control head in Wrangler JL and Gladiator JT interiors. The source documents several weeks of installed use and uses removable hook-and-loop fastening.

Left- and right-side mounting plates that bolt to the factory threaded inserts under the Gladiator JT dashboard tray. A separate short one-inch-style ball post can be positioned on either plate for compatible phone or radio arms.

Replacement adapter for mounting a REDARC Tow-Pro Liberty trailer-brake control knob in the Gladiator JT's twelve-volt power-outlet position. The source shows the completed physical installation.

Two- and three-gland spacers for routing additional wiring through the Gladiator JT factory bed-outlet opening. The source documents the required longer fasteners, edge protection, gasket, and heat-resistant material.

Soft slip-on window-sill armrest for a Gladiator JT door card. The flexible pad remains in place while the door and window operate, and its low profile is documented in installed and uninstalled physical views.

Two-piece protective shell for Wrangler JL and Gladiator JT key fobs. The bolted enclosure shields the panic button from accidental pocket presses while retaining access to the normal controls.

Flexible insulating boot for the disconnected cable end left by a non-invasive Gladiator JT auxiliary-battery delete. The source documents the installed cover after towing use and recommends securing its neck with tape.

Replacement panel for the Gladiator JT bed opening with provisions for one accessory switch and one twelve-volt socket. It fastens to four M4 rivet nuts and the source shows both the factory opening and completed installation.

Compact replacement housing for Wrangler JL and Gladiator JT key-fob electronics, factory buttons, battery, and screws. The selected revision-four top and bottom incorporate the creator's fit and stiffness updates.

Two-piece dashboard-pocket mount for a Yaesu FTM-500 control head in Wrangler JL and Gladiator JT vehicles. It requires no vehicle drilling and the source documents the installed assembly from three angles.

Two-piece six-switch panel that replaces the right-side media-center trim in Wrangler JL and Gladiator JT dashboards. The rear plate and switch retaining nuts clamp the assembly around the factory opening.

Small and large replacement caps for exposed interior trim screws in a Jeep Comanche MJ, including the larger fastener above the dome lamp. The source documents the physical prints and installed fit in several trim locations.

Console cupholder adapted specifically for Comanche MJ interiors with the parking brake on the floor. Two variants provide standard beverage wells, a small-can recess, and side slots for cards or change.

Screw-mounted cradle for securing a round CEC Industries EF33RL electronic flasher relay in a Willys CJ-2A. A zip tie retains the relay in the vehicle-specific bracket.

Two-color three-speed transmission shift knob developed for a 1971 Jeep CJ-5. The pattern insert and knob body are separate printable pieces, and the source documents the finished knob installed on its measured shifter.

Replacement pull knob for the air, temperature, or defroster cable controls used in Jeep CJ-5 and CJ-7 dashboards. The creator developed it after the factory temperature knob broke and reports the current geometry working.

Two-piece storage box for covering an oversized aftermarket-radio opening cut into a 1981 CJ-7 dashboard. Tabbed and plain halves glue together and convert the damaged opening into a useful cubby.

Original-style transmission and four-wheel-drive transfer-case shift knobs for Jeep CJ-7 controls. The printed bores are intended to be tapped for the vehicle's shifter threads after printing.

Speaker spacer rings developed while rebuilding a CJ-7 dashboard. They move replacement speakers away from the steel dash just enough for protruding tweeters to clear and are documented against the physical speaker assembly.

Two-piece steering-column cover for a CJ-7 converted to a Wrangler YJ tilt column. The right half includes a tachometer-wire clearance opening and threaded fastener points.

Under-dash bracket for a Nilight five-gang rocker-switch panel in a Jeep CJ-7. The source shows the installed panel and recommends heat-tapping the printed screw holes.

Adapter for fitting an older Omix-Ada 11020.01-style rear-view mirror to the newer windshield frame in a 1981 Jeep CJ-7. The source documents the printed adapter and physical installation.

Front and rear cupholder inserts designed and documented for a 2015 Jeep Compass. The two wells have different depths, so both fitted insert geometries are included; the creator expects first-generation 2007-2017 Compass compatibility.

Replacement center-armrest plug with an opening for a charging module, designed for a 2015 Jeep Compass. Source photos document the printed part, its armrest installation, and the charging-module fit.

Reinforced replacement sun-visor retainer designed after the original part broke in a 2014 Jeep Compass. The creator recommends ASA or ABS, or fully dense PETG, for cabin-temperature resistance.

Rear HVAC vent manifold and guide for the second-generation Jeep Compass. It installs behind the center-console vent trim and accepts one-inch corrugated hose to route air toward rear child seats; M2 fasteners secure the guides and clamps.

Fitted storage bin for the center console of 2022-and-newer Jeep Compass vehicles. The creator also reports compatibility with other model years sharing this console and the related Dodge Hornet console.

Left- and right-side fitted organizers for the open cubby beside the gear selector in a 2023 Jeep Compass. Both plain geometries are included for coins or other small cabin items.

Vehicle-fitted hook bracket for hanging a compact camping lamp from the upper cargo-area trim in a Jeep Patriot. The creator documents the printed bracket and lamp installed at the open tailgate.

Replacement retention clip for the rear tail-lamp assembly on a 2015 Jeep Patriot. The third-iteration geometry uses one #8 x 1-inch screw and avoids breaking the original clip during bulb service.

Fitted storage tray for the Jeep Renegade center armrest. The unbranded STL and editable STEP version are included; source photos document the tray seated in the console.

Replacement sun-visor retaining clip modeled from the broken original and installed by the creator in a 2016 Jeep Renegade.

Sunglasses retaining clip dimensioned specifically for the sun visor in a 2015 Jeep Renegade.

Replacement front plastic retainer for the Jeep Renegade cargo-cover lift string. The creator measured an intact counterpart and reports the printed piece fitting the vehicle.

Hand knob for removing the M8 spare-wheel retaining bolt in a Jeep Renegade without a separate tool.

Press-fit extender for the Jeep Renegade rear luggage-cover support. It increases engagement so the cover does not fall when the opposite side is being hooked in place.

Replacement socket-hinge piece for a broken Jeep Renegade sun visor. The creator printed the working part in PETG and documents it installed.

Replacement back shell plate for the rear camera assembly on a Jeep Renegade.

Replacement cap for a missing automatic shifter-knob insert, designed to fit a 2006 Jeep Commander.

Adapter designed for the rear HVAC outlet in a 2007 Jeep Commander. It accepts 1-1/8-inch bilge/discharge hose to route air toward a rear child seat, and the source documents the installed setup.

Replacement actuator plug for the Jeep Commander rear-seat release lever. Without the plug the seat release does not operate; the printable geometry directly replaces the discontinued original component.

Jeep Commander mounting set for attaching a compatible MOLLE organizer panel behind a front seat. The set includes the headrest bracket, lower connector, and retaining pin; M4 x 35 mm screws and 5 mm elastic cord complete the installation.