Jeep Gladiator JT 3D-printable parts

Two-piece six-switch panel that replaces the right-side media-center trim in Wrangler JL and Gladiator JT dashboards. The rear plate and switch retaining nuts clamp the assembly around the factory opening.

Two-piece dashboard-pocket mount for a Yaesu FTM-500 control head in Wrangler JL and Gladiator JT vehicles. It requires no vehicle drilling and the source documents the installed assembly from three angles.

Compact replacement housing for Wrangler JL and Gladiator JT key-fob electronics, factory buttons, battery, and screws. The selected revision-four top and bottom incorporate the creator's fit and stiffness updates.

Replacement panel for the Gladiator JT bed opening with provisions for one accessory switch and one twelve-volt socket. It fastens to four M4 rivet nuts and the source shows both the factory opening and completed installation.

Flexible insulating boot for the disconnected cable end left by a non-invasive Gladiator JT auxiliary-battery delete. The source documents the installed cover after towing use and recommends securing its neck with tape.

Two-piece protective shell for Wrangler JL and Gladiator JT key fobs. The bolted enclosure shields the panic button from accidental pocket presses while retaining access to the normal controls.

Left and right replacement brackets for the Mopar roll-up tonneau cover on 2020-and-newer Gladiator JT beds. Each bracket accepts two M5 threaded inserts; the creator reports that the pair fits and works.

Soft slip-on window-sill armrest for a Gladiator JT door card. The flexible pad remains in place while the door and window operate, and its low profile is documented in installed and uninstalled physical views.

Two- and three-gland spacers for routing additional wiring through the Gladiator JT factory bed-outlet opening. The source documents the required longer fasteners, edge protection, gasket, and heat-resistant material.

Replacement adapter for mounting a REDARC Tow-Pro Liberty trailer-brake control knob in the Gladiator JT's twelve-volt power-outlet position. The source shows the completed physical installation.

Left- and right-side mounting plates that bolt to the factory threaded inserts under the Gladiator JT dashboard tray. A separate short one-inch-style ball post can be positioned on either plate for compatible phone or radio arms.

Vehicle-specific dashboard-pocket mount for the ICOM IC-7100 control head in Wrangler JL and Gladiator JT interiors. The source documents several weeks of installed use and uses removable hook-and-loop fastening.

Nonconductive bracket for a Warn winch power-interrupt solenoid in the Gladiator JT engine bay. It uses an otherwise unused passenger-side body hole with an M6 rivnut; the creator also reports confirmed fitment from Wrangler JL and JLU owners.

Two-piece spring-loaded cargo cleat for the Gladiator JT Trail Rail system. The body indexes into the rail grooves and uses an M8 T-nut, threaded insert, and compression spring documented by the creator.

Contoured mount for round three-quarter-inch marker lights in the Gladiator JT grille. The geometry was developed specifically for the Gladiator grille rather than the Wrangler version, and the source documents the installed lights.

Snap-on flashlight holder for the factory front-seat track in Wrangler JL and Gladiator JT vehicles. It installs without drilling and the source documents both the printed clamp and its physical fit.

Replacement blank cover for the media-center opening in a Jeep Gladiator JT center dashboard. The source shows the printed cover fitted beside the factory switch bank.

Eight-millimeter gauges used when manually calibrating Freedom-panel position on Wrangler JL, JLU, and Gladiator JT roofs.

Tool-free magnetic holder for a Tazer JL Mini module under the dashboard of Wrangler JL or Gladiator JT models. It uses five 12 by 3 mm magnets and leaves the status light and USB port accessible.

A-pillar mount with two 20 mm accessory balls for Wrangler JL and Gladiator JT. It reuses the factory pillar bolt with a smaller replacement washer.

Printable W-type retaining clip sized for the fender-flare slots on 2018-and-newer Wrangler JL and compatible Gladiator JT applications. This entry uses the creator's support-free revision.

Three-hole adapter ring for fitting a Kicker-style 4-inch replacement speaker in the factory Wrangler JL or Gladiator JT speaker location.

Printable floor drain plug stated by the creator to fit Wrangler JK, Wrangler JL, and Gladiator JT floors and compatible drain openings in their floor mats. This entry contains only the functional plug body.