Jeep Grand Cherokee 3D-printable parts

Replacement control knob for a missing power-window switch on a 1997 Grand Cherokee ZJ. The creator iterated the fit and reports that the final geometry works correctly.

Replacement internal link that joins the driver-door window-switch button to its contact pins on a Grand Cherokee ZJ.

Replacement drive gear for a failed power-seat motion axis in a 1997 Grand Cherokee ZJ. The creator installed the printed gear after removing the broken original and documents the repaired mechanism.

Replacement push button for the exterior door-opening handle on a 1998 Grand Cherokee ZJ.

Threaded replacement hood-height stop measured from the original on a 1993 Grand Cherokee ZJ. The creator installed the part and recommends an under-hood material rather than PLA.

Replacement cupholder insert shaped for the Grand Cherokee ZJ center console.

Strengthened upper clip that retains the Grand Cherokee ZJ headlight reflector to its vertical adjuster. The source covers the full 1993–1998 ZJ range and documents the load-oriented print position.

Replacement transfer gear and pressure roller for the Grand Cherokee ZJ power-antenna drive. The creator installed the pair after the worn mechanism rattled and failed to extend fully.

Replacement roller for the scissor-type window regulator used in the Grand Cherokee ZJ. Three rollers service one regulator; the creator documents heat-assisted installation over the original ball-ended pins.

Replacement passenger-side interior release handle developed for a circa-1994 Grand Cherokee ZJ and installed in the vehicle. A heat-resistant cabin material and high infill are recommended.

Segmented inserts that replace the missing extruded-rubber strips in the stainless cargo-floor moldings of a Grand Cherokee ZJ. The segments are sized for a compact printer and conceal their joints after installation.

Blank replacement panel for the 1993–1998 Grand Cherokee ZJ Vehicle Information Center or Graphic Display Module opening. The panel provides a clean base for switches, gauges, or ports.

Radio fascia for adapting a single-DIN head unit to the factory radio opening in Grand Cherokee ZJ and export-model ZG dashboards. Locating pins reproduce the original mounting position.

Push-fit center cap modeled for 1993–1998 Grand Cherokee ZJ wheel hubs. The source includes an installed result and recommends PETG with supports.

Service funnel sized for the 19 mm automatic-transmission fill tube on a Grand Cherokee ZJ. Small sealing rings are included in the printed geometry.

Replacement headlight closure-panel lock ring modeled for a 1996 Grand Cherokee ZJ. The creator identifies possible use across the 1993–1998 generation.

Replacement sun-visor retaining clip designed and used on a Grand Cherokee ZJ after the factory clip failed.

Socket tool for removing the lower outer headlight adjuster on 1993–1998 Grand Cherokee ZJ assemblies.

Bolt-on bracket developed for mounting a three-inch auxiliary light above the front fender of a Grand Cherokee ZJ. The source documents the installed bracket from three angles.

Replacement square peg for the Grand Cherokee ZJ headlight-adjustment mechanism.

Rigid MOLLE/PALS panel for the 1996–1998 Grand Cherokee ZJ center console. Standard and no-spacer versions are included, with the installation sequence and finished use documented.

Replacement link between the HVAC blend-door actuator and lever on a 1998 Grand Cherokee ZJ.

Replacement strain-relief shell for the neutral-safety-switch electrical connector on a 1998 Grand Cherokee ZJ.

Replacement wing handle for the spare-tire retainer used in 1999–2004 Grand Cherokee WJ and WG cargo areas. The print captures a standard M10 × 1.5 hex nut.

Replacement wheel center cap for the Grand Cherokee WJ and WG. This entry uses the creator's rebuilt Fusion geometry rather than the heavier original scan mesh.

Replacement receptacle for the ball studs on 1999–2004 Grand Cherokee WJ and WG headlight housings. Three receptacles support each lamp while preserving adjustment movement.

Flexible replacement stop for the fuel-filler door on a Grand Cherokee WJ or WG.

Replacement interior hood-latch release handle developed for a 2001 Grand Cherokee WJ and WG after the factory handle broke.

Dashboard fascia blank for fitting a double-DIN radio to a Grand Cherokee WJ or export-model WG. The user cuts the final opening for the chosen head unit; the source documents the installed fit.

Replacement cupholder for Grand Cherokee WJ and WG center consoles. Moving the cup openings rearward adds a small forward storage pocket; the creator verified the fit in a 2004 vehicle.

Replacement pivot pin for the Grand Cherokee WJ and WG heater-core door mechanism. The source specifies solid horizontal printing for strength and alignment with the actuator motor.

Replacement diffuser modeled from the original under-hood service lamp on a Grand Cherokee WJ or WG.

Removable sizing sleeve for the oversized driver-side cup opening in a 2004 Grand Cherokee WJ or WG. It supports a standard 20-ounce drink bottle and was test-printed in PETG.

Two-piece replacement for the ashtray and accessory-socket panel in 1999–2004 Grand Cherokee WJ and WG center consoles. The layout supports five Carling switches, two seat-heater switches, and five accessory sockets while reusing the factory metal latches.

Repair insert for a failed P21W bulb socket in Grand Cherokee WJ and WG tail-lamp circuit boards. The source documents the replacement cartridge and wired installation.

Replacement sun-visor mounting clip for 1999–2004 Grand Cherokee WJ and WG interiors. The creator reports a perfect fit and provides the printable mesh alongside the original CAD.

Two-piece front-bumper retainer modeled from the fastener on a 2000 Grand Cherokee WJ. The creator verified the installed function and oriented the insert for layer strength.

Two-piece floor plug and hose fitting for the Grand Cherokee WJ and WG sunroof drain. The source documents installation with RTV or silicone sealing at the body joint.

Replacement fuse-puller tool stored at the Grand Cherokee WJ and WG fuse panel. The source documents both the factory storage position and the printed replacement.

Socket-style service wrench for the 74.5 mm, 14-flute oil-filter housing used by the 2007–2008 Grand Cherokee WK and WH with the 3.0L CRD diesel engine. The creator designed it from measured filter geometry and documented a physical test print.

Double-DIN radio mounting kit for 2008–2010 Grand Cherokee WK and WH dashboards. The creator leaves mounting holes undrilled for the chosen head unit and explicitly documents identical fitment in 2008–2010 Commander, 2008–2012 Liberty, and 2007–2017 Wrangler dashboards.

Replacement panel for the left-side dashboard cubby in 2008–2010 Grand Cherokee WK and WH interiors. The selected, creator-tested version holds five 20 mm round Hella H61923001-style switches; the untested square-hole variant is intentionally excluded.

Flexible replacement escutcheon for the fixed fender antenna on Grand Cherokee WK and WH vehicles. Two bore sizes are supplied for installation with a 21 mm outer-diameter, 14.5 mm inner-diameter sealing washer.

Replacement driver-side lock and unlock rocker for 2005–2010 Grand Cherokee WK and WH door-switch panels. It reuses the original spring and metal spring cap; the creator reverse-engineered and tested it from the failed factory button.

Two-piece housing that replaces the cigarette-lighter socket in a 2005 Grand Cherokee WK or WH and secures the USB extension from an aftermarket radio. The creator reports the assembly working in the vehicle.

Replacement outer cover for the front-passenger seat-belt anchor on a 2008 Grand Cherokee WK or WH. The source includes the factory part, printed geometry, and physical fit views.

Replacement trim retainer modeled from the surviving clip on a 2007 Grand Cherokee WK or WH. The creator printed it in PETG, installed it, and reports that it remained secure for several months.

Two-piece snap-together replacement eyelet for the cargo-floor tie-down points in a Grand Cherokee WK or WH.

Replacement drive gear for the power-adjustable accelerator-pedal mechanism in a Grand Cherokee WK or WH. The creator printed it solid in PETG, lubricated the thread, installed it, and reports restored adjustment.

Replacement sun-visor support bracket for 2005–2010 export Grand Cherokee WH and corresponding WK interiors. The source provides the finished physical print and matching CAD geometry.

Flexible replacement dust cover for the automatic shifter gate in 2005–2010 Grand Cherokee WK and WH center consoles. The creator documents the installed fit and specifies NinjaFlex.

Protective fitted sleeve for the key fob used with 2014 and 2016 Grand Cherokee WK2 vehicles. The creator documents the physical print around the complete fob.

Replacement internal gear for the air-conditioning actuator in a 2011 Grand Cherokee WK2. The printable geometry reproduces the failed compound gear and keyed center bore.

Pair of front license-plate brackets for a 2015 Grand Cherokee WK2 lower grille. Each bracket accepts a plate screw and fastens to the mesh with a zip tie, avoiding drilled holes; the creator documents the exact mounting location.

Replacement cargo hook modeled for a 2013 Grand Cherokee WK2 luggage area.

Reinforced hand wrench for removing and installing the H11 headlight bulb in a 2015 Grand Cherokee WK2's confined lamp housing. The selected version is the physically tested hand-tool geometry; the source warns that the bulb turns only one quarter turn.

Replacement body aperture plug for Grand Cherokee WK2 sheet-metal openings, modeled specifically as a substitute for the factory Mopar plug.

Two-piece cross divider for the standard, non-locking center-console bin. The creator physically verified it in 2021 and 2022 Grand Cherokee consoles; the selected version 3 adds beveled lower corners and supersedes the hand-sanded version 2.

Replacement center-console storage bin for a 2019 Grand Cherokee WK2 without Selec-Terrain. It recesses and supports a REDARC trailer-brake remote knob without drilling the dashboard; the corrected revision 2 file is selected and the creator documents the installed assembly.

Protective ring for the power-seat lumbar switch used in 2011 and 2014 Grand Cherokee WK2 interiors. It prevents accidental adjustment while reaching into the vehicle and mounts around the existing control with double-sided tape.

Clip-on guard for the Selec-Terrain drive-mode control in 2011–2021 Grand Cherokee WK2 center consoles. It prevents pets or cargo from pressing the control while preserving intentional access.

No-drill mount for a REDARC trailer-brake controller knob in Grand Cherokee WL interiors. It reuses a trim screw below the steering wheel, preserves steering-column movement and knee clearance, and can be stabilized with double-sided tape.