Jeep Wrangler YJ 3D-printable parts

Printable rear lamp housing with deeper lens-screw holes, a wiring opening and internal rails for the included red-and-clear lens separator. The source recommends heat-resistant material and provides both printable parts.

Replacement end clip for broken mechanical heater-control cables. The creator verified it on 1991 controls and identifies select CJ, YJ and XJ applications; fit and cable travel should be checked before reassembly.

Driver- and passenger-side replacement handles for paddle-style doors. The creator tested the design in a 1981 CJ-7 and states YJ and TJ compatibility, while warning that earlier non-paddle doors differ.

Printable rectangular taillight lens for the standard late-CJ and YJ rear lamp housing. The creator printed it in clear ABS for use with red and white LED bulbs.

Three-piece replacement cupholder with a 3.5-inch front pocket, a 1.91-inch rear pocket and a separate base that can be glued or screwed in place.

Cupholder that uses the stock windshield-mount-plate holes on late CJ and YJ vehicles without the factory dash pad. It is sized for a mug with a carabiner handle and the creator test-fitted a PETG print.

Snap-in plug for a flat one-inch floor drain hole. The source warns that a hole crossing a floor bend may need a slightly smaller plug.

Flexible gasket that seals between the rectangular taillight housing and lens. The source specifies TPU and the mounting pattern is documented across late CJ, YJ and TJ applications.

Left- and right-hand replacements for the break-prone plastic soft-top rail pins or sliders used on 1991 vehicles. Both original downloadable meshes are included.

Separate circular and rectangular flexible liners that replace the original rubber center-console insert without print supports. The physical photograph documents the original one-piece texture and layout.

Slip-on clip that holds the door courtesy-light switch open so the interior lights remain off when the doors are removed. It was designed around the pictured replacement switch.

Two printable plastic spacer components for repairing the horn-button assembly. The source only verifies the YJ application, so other same-era vehicles were not linked.

Paired stops that fit around the mirror-arm mounting nuts to limit mirror movement. The creator installed ABS prints and provides fitting cautions for seating the nut without overloading the part.

Four-piece left- and right-hand replacement set for the discontinued soft-top bow ends. Physical photographs compare the printed parts with the originals and show the assembly positioned on the body rail.

Close replica of the factory dashboard switch plate with openings for three standard toggle switches. The creator printed and installed the panel in PETG.

Two low-profile front turn-signal housings for LED conversions, with 12-by-12 and 20-by-20 heatsink openings. The creator installed the design to gain intercooler clearance while retaining the original lamp location.

Hooks that slip under the soft-top rails and accept shock cord or resized paracord to keep the folded top from moving.

Replacement retaining clip for the 2.5-litre airbox. The creator trial-fitted nylon prints on a 1990 vehicle, road-tested them and explicitly identifies the matching Comanche application.

Replacement slider knob for the defrost, heater and vent controls. It was measured from a broken original, physically compared with the original and test-fitted successfully.

Twist-on replacement cap for the windshield-washer fluid reservoir. The source notes that reservoir use requiring a vent tube is a different configuration and was not claimed.

Replacement door-hinge liners with separate early, later and driver-side printable variants. Source naming and year-marked files support late CJ, YJ and TJ applications.

Rear-seat cupholder that slides into the factory soft-top track and is retained by an existing track screw. The creator recommends high infill around the mounting tabs and upright.

License-plate bracket with a channel for an LED strip and a separate clear printable lens. The two-part design mounts in the stock late-CJ and YJ location.

Bracket for relocating a winch-controller jack into a grille slot. Exact grille spacing should be checked before drilling or wiring; speculative CJ and TJ fitment was not assigned.